Find the time constant, initial and final capacitor voltage. 30u(t) V +1 Time constant: 1.67 s A Initial voltage: 20 V Final voltage: 10 V Time constant: 0.6 s B Initial voltage: 20 V Final voltage: 10 V Time constant: 1.67 s Initial voltage: 10 V Final voltage: 20 V Time constant: 0.6 s D) Initial voltage: 10 V Final voltage: 20 V 10 Q2 www 20 Ω +1 V 114 t=0 F +1 10 V

Find the time constant, initial and final capacitor voltage. 30u(t) V +1 Time constant: 1.67 s A Initial voltage: 20 V Final voltage: 10 V Time constant: 0.6 s B Initial voltage: 20 V Final voltage: 10 V Time constant: 1.67 s Initial voltage: 10 V Final voltage: 20 V Time constant: 0.6 s D) Initial voltage: 10 V Final voltage: 20 V 10 Q2 www 20 Ω +1 V 114 t=0 F +1 10 V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
List the five capacitor replacement rules.
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
Question 4 A boost converter has an input of 5V and an output of 20W at 15V. The minimum inductor current must be no less than 50% of the average. The output voltage ripple must be less than 1%. The switching frequency is 30kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value. Verify your answers using Matlab, show the inductor current is continues and its minimum is no less than 50% of its average. Furthermore, the output voltage ripple is less than 1%.
Q6) The waveform of the voltage obtained after rectification is of a -----nature and therefore contains .harmonics a. Sinusoidal O b. Triangular c. Pulsating O d. Repetitive O
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
Three capacitors 6, 10 and 15 uF are connected in series across a 100 volt supply. Find the voltageacross the 10uF capacitor.
The capacitor dissipation factor is the ratio of inductive reactance to its resistance resistance to its inductive reactance resistance to its capacitive reactance capacitive reactance to its resistance
A Capacitor filter is used at the output across the load to minimize the ripple factor of the output voltage. If R = 20 02 and the single- phase bridge rectifier is supplied from a 120V - 60 Hz sinusoidal source. Find the capacitor value in millifarads that will maintain the amount of the output ripples to less than 5% 艹 Ce = m₂ 0 mF RL%
An inductance coil consumes 500W of power at 10A and 110V and 60HZ. Determine the resistance and the inductance of the coil
1)The value of the capacitance reactive power in VAR is? /2) The value of the capacitor in micro farad is?
Through a capacitor of capacitance 15 micro-farad with a frequency of 50 hz. Compute its reactance 212 ohms O 4,712 ohms O 0.0047 ohm O 0.0002 ohm