Ex] A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75 inch and the pitch diam of 3 inches. The pressure angle is 14.5° and the coefficient of friction is 0.12. a) Find the tangential force on the gear. b) Find tangential force on worm. c) Find the separating force

Ex] A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75 inch and the pitch diam of 3 inches. The pressure angle is 14.5° and the coefficient of friction is 0.12. a) Find the tangential force on the gear. b) Find tangential force on worm. c) Find the separating force

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two mating involute spur gears of 20 pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length cach, find: i) the addendum for pinion and gear wheel, i) the length of arc of contact, iiithe maximum velocity of sliding during approach and recess. Assume pinion to be driver.
Q2/ Two mating involute spur gears of 20* pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on cach wheel is such that the path of approach and the path of recess on cach side are half the maximum possible length each, find: i) the addendum for pinion and gear wheel, ii) the length of arc of contact, iii)the maximum velocity of sliding during approach and recess. Assume pinion to be driver.
1. Calculate the power that can be transmitted safely by a pair of spur gears with the data given below. Calculate also the bending stresses induced in the two wheels when the pair transmits this power. Number of teeth in the pinion = 20 Number of teeth in the gear = 80 Module = 4 mm Width of teeth = 60 mm Tooth profile = 20° involute Allowable bending strength of the material = 200 MPa, for pinion = 160 MPa, for gear = 400 r.p.m. Speed of the pinion Service factor = 0.8 0.912 0.154- T Lewis form factor %3D 3 Velocity factor 3 + v
7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative image) has 48 teeth on front sprocket (Crank side), the diameter of front sprocket being 10.5 inches. The rear wheel has a cassette with a cluster of 6 sprockets, with number of teeth on Sprocket #1 (lowest gear) to Sprocket # 6 (highest gear) being 30, 26, 23, 20, 16 and 12, respectively. (Ignore wind resistance and friction between machine elements) (a) If the rider is pedaling at a constant 105 rpm with an effective force of 28 lb acting on periphery of front Sprocket (at 5.25 inch radius length, the force location indicated by red arrow), and is engaged in Sprocket #5, what would be the torque acting on Sprocket # 5, and the RPM at which the rear wheel is spinning? (b) For the condition as described in (a), If the diameter of wheels is 26 inches, what is the speed of the bicycle? &
In the figure below the gears are 20º full depth of AGMA Quality No 8. a) Find the horsepower transmitted by the 1-2 mesh b) Find the required width b for the 3-4 mesh if they are carrying the same horsepower as the 1-2 mesh. No.2, C.I. BHN=220 P=4, N₂=72,b=2" No 1, Steel, P=4, N₁=24,b=2" n₁ = 570 rpm /No.4.CI. BHN=220 P=3, N₂=72 No.3, Steel, P=3, N₁=24
4. A double threaded worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75" and pitch diameter is 3". The pressure angle is 14.5 degrees and coefficient of friction is 0.12. Find the worm gear efficiency.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratio
c) Two gear wheels with 50 and 30 teeth respectively, mesh externally, the speed of the smaller being 1800 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 18° involute form, addendum length is 8 mm and the module is 5 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact.
Two meshing spur gears with 20 pressure angle have a module of 4 mm. The centre distance is 220 mm and the number of teeth on the pinion is 40. What should be the new centre distance so that pressure angle is increased to 22°? (Ans. 221.9 mm).
The following data relate to a pair of 20° involute gears in mesh:Module = 6 mm, Number of teeth on pinion = 17, Number of teeth on gear =49; Addenda on pinion and gear wheel 1 module.Find: a)The number of pairs of teeth in contact; b)The angle turned through bythe pinion and the gear wheel when one pair of teeth is in contact, andc)The ratio of sliding to rolling motion when the tip of a tooth on the largerwheel (i) is just making contact, (ii) is just leaving contact with its matingtooth, and (iii) is at the pitch point.(14
A worm drive transmits 15 kW at 2000 rpm to a worm gear having 90 teeth with 6mm module. The worm is triple threaded and has 65 mm pitch diameter. The tooth form is to be 20 degrees full depth involute. Determine: a) the lead and lead angle of the worm A. b) The center distance between worm and gear. c) The tangential force acting on worm. d) The axial force acting on worm e) The radial force acting on worm
Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The pressure angle is 20° with a module = 2 mm. Determine the following: a. Draw the free body diagram for the gear set. b. Pitch diameters of each gear. 50T of m b. 3 30T - 20T C. Transmitted load on gear 2. d. Torque on gear 2 shaft a. e. Tangential and radial force from gear 2 shaft. f. Tangential and radial forces on gear 4. g. Torque on gear 4 shaft c.