Consider a tube of inner and outer tadii ri and ro, whose temperatures are maintained at Ti and To, respectively. The thermal conductivity of the cylinder is temperature dependent and may be respresented by an expression of the form k=ko(1+aT), where ko and a are constants. Obtain an expression for the heat transfer rate per unit length of the tube. What is the thermal resistance of the tube wall?

Consider a tube of inner and outer tadii ri and ro, whose temperatures are maintained at Ti and To, respectively. The thermal conductivity of the cylinder is temperature dependent and may be respresented by an expression of the form k=ko(1+aT), where ko and a are constants. Obtain an expression for the heat transfer rate per unit length of the tube. What is the thermal resistance of the tube wall?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.34P: A section of a composite wall with the dimensions shown below has uniform temperatures of 200C and...

See similar textbooks

Similar questions

Estimate the rate of heat loss per unit length from a 5-cm ID, 6-cm OD steel pipe covered with high-temperature insulation having a thermal conductivity of 0.11 W/(m K) and a thickness of 1.2 cm. Steam flows in the pipe. It has a quality of 99% and is at 150C. The unit thermal resistance at the inner wall is 0.0026(m2K)/W the heat transfer coefficient at the outer surface is 17W/(m2K) and the ambient temperature is 16C.
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
2.7 A very thin silicon chip is bonded to a 6-mm thick aluminum substrate by a 0.02-mm thick epoxy glue. Both surfaces of this chip-aluminum system are cooled by air at , where the convective heat transfer coefficient of air flow is . If the heat dissipation per unit area from the chip is under steady-state conditions, draw the thermal circuit for the system and determine the operating temperature of the chip.
2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)
Water at a temperature of 77C is to be evaporated slowly in a vessel. The water is in a low-pressure container surrounded by steam as shown in the sketch below. The steam is condensing at 107C. The overall heat transfer coefficient between the water and the steam is 1100W/m2K. Calculate the surface area of the container that is required to evaporate water at a rate of 0.01 kg/s. Problem 1.16
A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6
A section of a composite wall with the dimensions shown below has uniform temperatures of 200C and 50C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials are: kA=70W/mK,kB=60W/mK, kC=40W/mK, and kD=20W/mK, determine the rate of heat transfer through this section of the wall and the temperatures at the interfaces.
2.29 In a cylindrical fuel rod of a nuclear reactor, heat is generated internally according to the equation where = local rate of heat generation per unit volume at r = outside radius = rate of heat generation per unit volume at the centerline Calculate the temperature drop from the centerline to the surface for a 2.5-cm-diameter rod having a thermal conductivity of if the rate of heat removal from its surface is 1.6 .
A pipe wall with inner and outer radii ri and ro, whose temperatures are kept in Tj and To, is discussed. The heat transfer coefficient of the cylinder depends on the temperature, and k = ko (1 + aT) relationship can be written, where k, and a are constant. Subtract an equation for the heat passing through the unit length of the pipe. What is the thermal resistance of the pipe wall.
Choose the false statement? We can express lumped capacitance relation as the combination of Biot and Fourier numbers At very low values of Prandtl number, material has higher thermal conductivity compared to its momentum diffusivity We can calculate convective heat transfer coefficient from Nusselt number If Biot number is less than 0.1, we can neglect thermal resistance in some direction None of the given
A pipe wall with inner and outer radii r, and ro, whose temperatures are kept in Tj and To, is discussed. The heat transfer coefficient of the cylinder depends on the temperature, and k = ko (1 + aT) relationship can be written, where k, and a are constant. Subtract an equation for the heat passing through the unit length of the pipe. What is the thermal resistance of the pipe wall.
1. Saturated steam at 500 K flows in a 0.20 m inside diameter, 0.21 m outside diameter pipe. The pipe is covered with 0.075 m of insulation with a thermal conductivity of 0.10 W/m-K. The pipe's conductivity is 52 W/m-K. The ambient temperature is 300 K. The unit convective coefficients are hi = 18,000 W/m²-K and ho 12 W/m²-K. Determine the heat loss (kJ/min) from 5 m of pipe.