Draw a full-wave bridge rectifier circuit (use multisim) connected to a load resistance of 470 Q, with input VPP= 29 V. Connect a voltmeter across the load and an ammeter to measure the current through the load. Peak voltage of the output from the graph Average voltage across the load from the voltmeter reading Average current from the ammeter reading

Draw a full-wave bridge rectifier circuit (use multisim) connected to a load resistance of 470 Q, with input VPP= 29 V. Connect a voltmeter across the load and an ammeter to measure the current through the load. Peak voltage of the output from the graph Average voltage across the load from the voltmeter reading Average current from the ammeter reading

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
What is CEMF?
A single-phase full-wave bridge rectifier circuit is fed from a 220 V, 50 Hz supply. It consists of four diodes, a load resistance 20 Q and a very large inductance so that the load current is constant. What is the average or dc output voltage?
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 Q. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 Q. Mean load current will be
Full Wave Rectifier Numerical Question: A full wave rectifier circuit is constructed using a bridge rectifier configuration consisting of four diodes and connected to an AC voltage source. The AC voltage source has a peak voltage of 120 V and operates at a frequency of 60 Hz. The load resistor connected to the output terminals of the rectifier has a resistance of 1 k. Each diode in the bridge has a forward voltage drop of 0.6 V. Calculate: 1. The peak voltage of the rectified output. 2. The average output voltage. 3. The peak inverse voltage (PIV) of the diodes. 4. The ripple voltage (peak-to-peak) of the output.
2. A simple half wave rectifier consists of a diode and load. If the internal resistance of the diode is 1 ohm and the load resistance is 5 ohms. What will be the DC load current if the supply voltage is 12 Volts, draw the schematic diagram and also draw the waveform of the rectifier. 3. Determine the output voltage in the figure below Si Ge Vo R₁ 2kQ 20V R2 2kQ
Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
Be a single-phase half-wave rectifier with an RL load. The sinusoidal input voltage has a frequency of 60 Hz and the value of R = 10 ohms. What is the value of L for the current extinction angle to be 270°. Tip: use Puschlowski's abacus.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…