C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is applied to the input signal VIn? 10k D1 R2 LM324 VEE 주 02 10k out UTA Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When Vin is positive the circuit conducts but only to one diode drop, B. When Vin is negative the circuit operates as an inverting amplifier providing an inverted sine wave at Vour. When VIN Is positive the circult is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When Vin is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VouT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at VoUT. When Vin is positive the circuit conducts but only to one diode drop.

C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is applied to the input signal VIn? 10k D1 R2 LM324 VEE 주 02 10k out UTA Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When Vin is positive the circuit conducts but only to one diode drop, B. When Vin is negative the circuit operates as an inverting amplifier providing an inverted sine wave at Vour. When VIN Is positive the circult is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When Vin is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VouT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at VoUT. When Vin is positive the circuit conducts but only to one diode drop.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Be a single-phase half-wave rectifier with an RL load. The sinusoidal input voltage has a frequency of 60 Hz and the value of R = 10 ohms. What is the value of L for the current extinction angle to be 270°. Tip: use Puschlowski's abacus.
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
Aasty VIJlc gn, ödljö A dziall jajc D Q4. For the following bridge rectifier circuit, draw the output voltage waveform across the load (RL) showing the maximum value. Calculate the following: The average value of the output voltage across the load (RL). a. b. The rms value of the output voltage across the load (RL). c. The average load current. d. The rms value of the load current. (Use constant voltage drop model for the Silicon diode) 5:1 110 Vrms Assignment1- (ENEL2104) Page 2
Q2) For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KO resistor) and the load current (through the load 2.2 KN resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode D1). The input Vi is sinusoidal with maximum amplitude (peak) of 14.1422 V and frequency of 60 Hz. The diode D1 is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
Determine the output voltage of a Half-wave rectifier with an input peak-to-peak sinusoidal voltage of Vm.
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.
S-4) The input signal Vin of the clipper circuit given below is a sinusoidal signal of Vp-p = 30V and the wave the form is as given in the figure. a) Plot the output waveform of this circuit in the area given for + and - alternans. b) Calculate the peak values of the output and indicate it on the graph. Note: Diode threshold voltage will be 0.7V
Draw circuit diagram of a full-wave controlled rectifier and draw the wave shapes of output voltage and current for R-L load with sinusoidal input. You have to design a full-wave AC to DC converter circuit to have output average voltage of 40 and 50 W power to a 100 Ω resistive load from a source of 60 V. Is the design feasible? Why?
H.W3 The single-phase full wave controlled rectifier has a R-L load with R= 0.552 and L= 6.5mH. The input voltage V, 220V at 50Hz. The delay angle is a-30, plot the input and output waveforms. Then determine: -The average thyristor current -The rms thyristor current -The output rms current -The average output current - The efficiency NOTE: Drive any formula that used in solution
Design the Clipper-Clamper circuit to perform the output waveform shown in figure below. GaAs Diode GaAs Diode Vo f=1 kHz. 3 V + -3V Clipper Clamper -13 V -10 V
Draw circuit diagram of a half /full-wave single- / three-phase controlled rectifier and draw the wave shapes of output voltage and current for R / R-L load with sinusoidal input.