i need the answer quickly J LUmect the AVO meterDISCUSSION1 Compare between the practical and theoretical results for input and outputvoltages.2. What design parameters of the full wave single-phase rectifier?3. When you design 10kW rectifier, what type of rectifier must be use?Why? J4. Desigh a Carbon dioxide laser power supply, if the voltage acrossdischarge tube is 12kVolt and the current pass through discharge tube is100mA

Answered: Image /qna-images/answer/b7207324-6bf7-43f4-b7aa-a67a80835e9e.jpg

Answered: DISCUSSION

Engineering

Electrical Engineering

DISCUSSION

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
Design a controlled half wave rectifier circuit to produce an average of 30 V across a 250 ohm load resistor from a 220 Volt max 50 Hz AC source. Determine the power absorbed by the resistance. What would be the average voltage value if diodes were used in this circuit? no chat GPT, only hand written please otherwise leave a DOWNVOTE
For the full wave rectifier circuit shown in Figure 1, calculate: 1) The maximum current through the load. 2) The average current through the load. 3) The average voltage across the load. 4) The rms value of the current. 5) The rectification efficiency. Vms = 280V Vin RL= 12ks2 Vrms = 280V Figure 1
A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
-,- three phase half wave controlled rectifier with resistive load (R=10 2) if the input supply voltage is (Vrms = 380 Volt and f= 50 Hz) and the trigger angle (a = 60°), then determine the followings:- a) Draw the rectifier circuit. b) Draw to scale the input voltage, the load voltage and the current waveforins. c) Calculate the average value of the output voltage.
the three phase half wave uncontrolled rectifier is operated from 500v,50Hz supply at secondary side and the load resistance is 25 ohms. if the source inductance is negligible, determine a) rectification efficiency b) form factor c) ripple factor d) transformer utilization factor e) peak inverse voltage of each diode
Asap
# Example 3 For a center tapped transformer coupled full wave rectifier, if 100 V peak sine wave (60Hz) is applied, what will be the rectifier's output voltage and PIV for each of the diode? Assume transformer turns n=0.2.
Discussion: 1- Calculate the theoretical output DC voltage of the half wave rectifier circuit and compare it with measured value. For the capacitive filter, obtain the theoretical values of the DC output voltage and the ripple voltage and compare these values with the measured quantities. 2- Explain the effect of increasing the filter capacitance on the output voltage. 3- What is the difference between Half-Wave Rectifier and Full -Wave Rectifier? 4- What is the advantages and disadvantages of Full-Wave Bridge Rectifier over Half Wave Rectifier?
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019