three phase half wave controlled rectifier with resistive load (R=10 2) if the input supply voltage is (Vrms = 380 Volt and f= 50 Hz) and the trigger angle (a = 60°), then determine the followings:- a) Draw the rectifier circuit. b) Draw to scale the input voltage, the load voltage and the current waveforins. c) Calculate the average value of the output voltage.

three phase half wave controlled rectifier with resistive load (R=10 2) if the input supply voltage is (Vrms = 380 Volt and f= 50 Hz) and the trigger angle (a = 60°), then determine the followings:- a) Draw the rectifier circuit. b) Draw to scale the input voltage, the load voltage and the current waveforins. c) Calculate the average value of the output voltage.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: 4. DC load voltage Ripple factor C.
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
.Draw a full-wave rectifier circuit (using a diode bridge) and predict the output voltage signal when the input is a sinusoidal signal with amplitude 10 V (p p). Use the previous full wave rectifier to create a peak detector with a 2 V ripple.
A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?
(i) Draw the circuit diagram of single phase fully controlled bridge rectifier with RL load and write the current path for negative half cycle operation. (ii) Plot the output voltage and current waveforms for firing pulse is 60° .
Q-2: A singie phase fiull-wave controlled rectifier is connected to RL load (R-15 ohm and 1.-20mH ). Vs- 240 and 50 Hz supply When the firing angle is a=55. Deternine: A} the average voltage and average current in the load. B) The form factor and ripple factor. C) Peak inverse voltage of the thyristor.
A single-phase center-tapped rectifier has an R-L of R= 20 0, L = 50mH, and a 240 V ac 50 Hz source voltage. Determine: i. The average and rms currents of the diodes and the load. ii. The rms and average 50 Hz source currents. iii. The power absorbed by the load. iv. The supply power factor.
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
3. A three phase half-wave continuous load current controlled rectifier has a supply of 150V/phase. Determine the load voltage for firing delay angle of 0°, 30° and 60°. Assuming a thyristor voltage drop of 1.5V.
H.W - For a three phase half wave controlled rectifier with resistive load if the input supply voltage is (Vrms 380 Volt and f= 50 Hz) and the trigger angle (a = 90°), (R-10 S2), Then determine the followings:- 1. Draw the rectifier circuit. 2. Draw to scale the input voltage, the load voltage and the current waveforms. 3. Determine the mean values of the load voltage and load current.
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consisting series connected a resistor and an inductance from a 70.7V (RMS), 50HZ sinusoidal AC source. The firing delay of the thyristor is 90° and the load values are R=10Q, L=0.1 H. Define the load current expression and draw the load current by calculating for first two periods. And calculate the average values of the load voltage and current.