Design the required rectangular sedimentation tank(s) for a water treatment plant given thefollowing information:•.Flow rate: 37, 900 m³/dDetention time: 3.1 hoursSurface loading rate (overflow rate): 38 (m³/d)/m²L = 4 WWeir loading rate: 240 m³/m/day. The weir should be designed to achieve the geometrygiven below. Find the value of Width of Basin (W), Length of Basin (L), Total WeirLength and Value of "b" below.(W-2)00-1

Here is some information you can use, hope it can help you and God bless.

Answered: Design the required rectangular…

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.7CTP

See similar textbooks

Similar questions

Read the question carefully and give me both a&b right solutions. A 1.3-m wide rectangular channel with a bed slope of 0.00019 has a depth of flow of 0.8m. Manning’s roughness coefficient is 0.017. (a) Can Manning’s equation be applied to this system (i.e., is the flow fully turbulent)? (b) Regardless of the answer to part a, determine the steady uniform discharge in the channel.
1. Design a pipe culvert using the following data. Also, draw the longitudinal section of the culvert. Discharge in the stream: 4 m/s Road top level: 106 m Road bottom level: 101.5 m Road width: 7.5 m with 1 m wide shoulders Density of the soil at site: 18 kN/m3 Loading: IRC Class A C. = 1.8
A concrete-lined trapezoidal channel has to be constructed to carry a discharge of 500 cfs. Design the channel. Assume that the following values were fixed based on the site conditions: • Bed slope = 0.002 • n = 0.015 • Side slope, z = 1 (vertical):1.5 (horizontal) • b/y ratio = 2.0
. Refer to the following channel cross section. Normal depth is 3.0 feet. (a) What is the cross-sectional area of flow? (b) What is the wetted perimeter? (c) What is the hydraulic radius? 3.0' 1.5' 1.5' 8) noio222013 (6) -5.0'- JadW (d) O Cengage Learning 2014
Design a weir according to the following data: Channel width = 6 m. Flow discharge = 5 m³/s. Upstream water depth = 1.5 m. Adopt Ca=0.65. 1
A- Proportional flow weir is used to keep constant horizontal velocity in: 1. Primary sedimentation tank 2. Areation tank 3. Grit removal chamber 4. Screen Hve
A circular settling basin is anticipated to receive a flow of 3.5 MGD. The tank is to be designed to have an overflow rate of 800 gpd/ft2. The depth is to be 11 ft. Determine the diameter of the basin (in feet). ? What length of weir (ft) is required to achieve a weir loading of 15,000 gpd/ft show all work
In 28.5 secs, 35,579 L of water is collected. The length of the rectangular weir is 2.15 m, the crest is 450 mm high from the channel bed and it should maintain a constant head of 275 mm. Determine the coefficient of discharge. Assume there is head loss. show your complete solution
In culverts design under outlet control, if the desired Manning coefficient is 0.02. The corrected culvert length of the culvert would increase. * False True For the logarithmic normal distribution fitting in the flood forecasting. The discharged should be ranked in a logarithmic order. * False O True For Manning's Equation, the letter A/P represents the hydraulic radius. * False O True
An unlined canal under regime conditions along with a silt factor of 1 has a width of flow 71.25 m. Assuming the unlined canal as a wide channel, the corresponding average depth of flow (in m, round off to two decimal places) in the canal will be Enter Your Answer... Check
A Circular primary sedimentation tank for a municipal WWTP is to be designed for an average flowrate 6400 m³/s, depth is 3 m, overflow rate 35 m³/m².d and weir loading is 180 m³/m.d. Determine diameter of tank, detention time and weir length. If unsure let others do. Don't do wrong and waste my question
Q#1(a) Water flows over a rectangular weir 3m long. The height of water surface over the weir is 1m. Calculate discharge over the weir by: Simple formula Francis’ formula Take Cd=0.62 and velocity of approach=2m/sec. Find the difference between the two discharges. (b) What is meant by “Hydraulic coefficient”? Explain different types of hydraulic coefficients. (c) What is a “Cippoletti weir” ?Prove that the side slope of a Cippoletti weir is 1:4.

SEE MORE QUESTIONS

Recommended textbooks for you

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning