Design a second order LPF, with unity de gain, to realize the following natural modes P1,2 = 10¹ (cos(144⁰) F jsin(144°)) based on method of inductor replacement i.e. (Antoniou inductance simulation cct.). Select appropriate components values and plot the final circuit, assign the values of the components on the circuit diagram, and write the resulted T (s). chop

Design a second order LPF, with unity de gain, to realize the following natural modes P1,2 = 10¹ (cos(144⁰) F jsin(144°)) based on method of inductor replacement i.e. (Antoniou inductance simulation cct.). Select appropriate components values and plot the final circuit, assign the values of the components on the circuit diagram, and write the resulted T (s). chop

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the nominal pi model which among these are divided into two halves? a. Series impedance O b. None of these. c. Shunt capacitance d. Both (A) and (B)
A step-down chopper is to be used to supply power from a 600-V overhead wire to the commutator motor on a trolley bus. The motor may be mod- eled as a generated direct voltage in series with a resistance of 0.2 and an inductance of 25 mH. The frequency of the chopper is set at 500 Hz. (a) When the bus is stopped, what should be the ON time of the chopper to provide a motor current of 150 A? (b) What is the maximum possible generated voltage of the motor for which a current of 150 A can be supplied? (c) What is the average value of the supply current for the conditions of (a) and (b)? បទៅនឹងរស់របស (d) If the motor current is to be continuous, what should be its minimum. value?
Use A 2 for CCM and lamda=1/2 for DCM. Design a CCM Boost Converter to output 48V at 10W with 2% ripple froma source that variesbetween 10-14 VDC witha PWM switching frequency of 25 kHz. Compute also the minimum inductance and capacitance that meets the circuit specification.
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : V. Find the peak and mean of the switch current.
Describe the steady-state similarities and differences of DC and AC circuits with purelyresistive elements
Input voltage VI is a DC signal. Do not repost other solutions to similar questions. Thank you.
aDefine the terms- O Front chopped Impulse wave; (1) Impulse flash over voltage. A six-stage impulse generator designed to generate the standard waveform (1.2/5 us) has a per stage capacitance of 0.06 uF to be used to test transformers with an equivalent winding to earth capacitance of 1 nF. A peak output voltage of 550 kV is required for testing the transformer. ) Draw the basic circuit diagram of the multi-stage impulse generator indicating all relevant values on it. (0.5 Mark) (i1) Calculate the wave front, wave tail control resistors and maximum impulse voltage output from the generator. (2.5 Marks ) - BI
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/2. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state: i. Draw the converter circuit. ii. Determine the inductor's turn ratio. iii. Determine the primary inductance. Sketch the diode current and switch current. iv V. Find the peak and mean of the switch current.
1) A dc-dc buck converter has a 48 V input. This converter is connected to a dc motor that spins at 2000 RPM given 24 V at its terminals, 1000 RPM for 12 V, and follows a linear speed relation at other voltages. The motor is characterized by a voltage source in series with an inductance and resistance. The resistance is 0.5 2. The inductance is 10 mH. The converter switches at 20 kHz. At 2000 RPM with no mechanical load, the motor draws 0.5 A. a) What is the no-load motor speed at 20% duty ratio? At 65% duty ratio? b) The buck converter has been set to operate the motor at 2500 RPM, when the FET abruptly turns off. Sketch the motor current after this turn-off. Where in the circuit does the current flow? When does it equal zero? (You may assume the motor electromagnetic field [EMF] remains constant after the FET turns off.)
Please solve this problem in detail A step up DC converter is used to control power flow from a DC votage Vs = 100V to a battery voltage E = 200V. The power transferred to the battery is 20 kw. The current ripple of the inductor is negligible. The duty cycle and the effective load resistance as seen from the input are respectively equal to: Select one: a. None of these b. 0.5, 0.5 Ohms c. 0.33, 0.5 Ohms d. 0.5, 0.33 Ohms
A high voltage engineer cascades 6 stages of a voltage doubler circuit to analyze effectiveness of doing so. Each capacitor in the circuit is 15 nF, of the input Asupply is 100 kv at Frequency 100 Hz. . so this voltages not enough with one moudle.So How much moudle can be in cascades fashion if the load current is 1 mA.
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : i. Draw the converter circuit.