Create an excel program that can solve an engineering non-linear equation using the following methods. You can choose your own non-linear equation. Make sure to explain what is the use of the equation. a) Bisection Method (200 iterations) (15%) b) Regula Falsi / False-Position Method (200 iterations) (15%) c) Simple Fixed Point Iteration (200 iterations) (15%) d) Newton Raphson method (200 iterations) (15%

Create an excel program that can solve an engineering non-linear equation using the following methods. You can choose your own non-linear equation. Make sure to explain what is the use of the equation. a) Bisection Method (200 iterations) (15%) b) Regula Falsi / False-Position Method (200 iterations) (15%) c) Simple Fixed Point Iteration (200 iterations) (15%) d) Newton Raphson method (200 iterations) (15%

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter14: Numerical Methods

Section: Chapter Questions

Problem 5PP

See similar textbooks

Similar questions

a)Write a computer program for the Gauss elimination method using the C programming language. Decide the number of significant figures yourselves. While writing your program, consider the effects of the number of significant figures, pivoting, scaling, and do not forget to check if the system is ill-conditioned.b)Repeat the same procedures for the Gauss-Jordan method.c)Solve an example system using your Gauss elimination and Gauss-Jordan method. Measure the time your computer solves the system for both programs.d)Write a report in which you discuss and compare your Gauss elimination and Gauss-Jordan programs. NOTE: BY USING C PROGRAMMING PLEASE SOLVE THIS QUESTION STEP BY STEP TO UNDERSTAND WELL.THE SUBJECT (Numerical Methods for Engineers) THANK YOU FOR HELPING AND HAVE A NICE DAY. I WILL RATE THE COMPLETE ANSWER
Write computer codes using any programming language for one of the following methods to solve a linear equation system.1- Gaussian elimination.2- LU decomposition.3- Gauss-Seidel iterations.Execute the program for the linear equation system given below.
Computer Science Develop a Python program that will use the Maclaurin series, to estimate f(x)=sinx at x=0.5 to a degree of accuracy where relative error is less than 0.1%. The program should return both the estimate of and the number of terms in the approximation.
The spring in the figure below is stretched from its equilibrium position at x = 0 to a positive coordinate xo. ko HINT x = 0 x = xo PE sn PE 50 The force on the spring is F and it stores elastic potential energy PESO. If the spring displacement is tripled to 3x, determine the ratio of the new force to the original force, and the ratio of the new to the original elastic potential energy, Fo Fo PESO (a) the ratio of the new force to the original force, PE ST PE SO (b) the ratio of the new to the original elastic potential energy,
Matlab A rocket is launched vertically and at t-0, the rocket's engine shuts down. At that time, the rocket has reached an altitude of ho- 500 m and is rising at a velocity of t125 m/s. Gravity then takes over. The height of the rocket as a function of time is: h(t)- ho+vot-gt², t20 where g = 9.81 m/s². The time t=0 marks the time the engine shuts off. After this time, the rocket continues to rise and reaches a maximum height of himax meters at time t-tmax. Then, it begins to drop and reaches the ground at time t = tg. a. Create a vector for times from 0 to 30 seconds using an increment of 2 s. b. Use a for loop to compute h(t) for the time vector created in Part (a). e. Create a plot of the height versus time for the vectors defined in Part (a) and (b). Mark the z and y axes of the plot using appropriate labels. d. Noting that the rocket reaches a maximum height, Amax, when the height function, h(t), attains a maxima, compute the time at which this occurs, tmax, and the maximum…
9. write algorithm to find the result of the following equation: (-х, х <0 x 2 0 f(x) =
For f(1) = r³ – 4, perform 3 iterations of Newton's method with starting point ro = 2. (By hand, but use a calculator.) Calculate the solution (r* = 4/3) on a calculator and find the errors and percentage errors of ro, 11, T, and 13. Use enough digits so that you do not falsely conclude the error is zero. Put the results in a table.
(Mechanics) The deflection at any point along the centerline of a cantilevered beam, such as the one used for a balcony (see Figure 5.15), when a load is distributed evenly along the beam is given by this formula: d=wx224EI(x2+6l24lx) d is the deflection at location x (ft). xisthedistancefromthesecuredend( ft).wistheweightplacedattheendofthebeam( lbs/ft).listhebeamlength( ft). Eisthemodulesofelasticity( lbs/f t 2 ).Iisthesecondmomentofinertia( f t 4 ). For the beam shown in Figure 5.15, the second moment of inertia is determined as follows: l=bh312 b is the beam’s base. h is the beam’s height. Using these formulas, write, compile, and run a C++ program that determines and displays a table of the deflection for a cantilevered pine beam at half-foot increments along its length, using the following data: w=200lbs/ftl=3ftE=187.2106lb/ft2b=.2fth=.3ft
Matlab A rocket is launched vertically and at t-0, the rocket's engine shuts down. At that time, the rocket has reached an altitude of ho- 500 m and is rising at a velocity of to 125 m/s. Gravity then takes over. The height of the rocket as a function of time is: h(t)-ho+vot-gt², t20 where g -9.81 m/s². The time t-0 marks the time the engine shuts off. After this time, the rocket continues to rise and reaches a maximum height of Amax meters at time t = tmax. Then, it begins to drop and reaches the ground at time t = tg. a. Create a vector for times from 0 to 30 seconds using an increment of 2 s. b. Use a for loop to compute h(t) for the time vector created in Part (a). e. Create a plot of the height versus time for the vectors defined in Part (a) and (b). Mark the and y axes of the plot using appropriate labels. d. Noting that the rocket reaches a maximum height, max, when the height function, h(t), attains a maxima, compute the time at which this occurs, max, and the maximum height,…
Newton's Law of Cooling My Solutions > A cheesecake is taken out of the oven with an ideal internal temperature of 165°F, and is placed into a 35°F refrigerator. After 10 minutes, the cheesecake has cooled to 150°F. If we must wait until the cheesecake has cooled to 70°F before we eat it, how long will we have to wait? Solve the equation via MATLAB making sure that you passed though the following: 1. Initialization of variables 2. Setting up the differential equations 3. Listing down initial conditions 4. Solving for the parameter k. 5. Finding the resulting model 6. Finding the period where the temperature will be 700 F. 7. Graph the solutions
Going missing Some calculations involving blank values may give different results to what you might expect. For example, when you pass a blank value into the AND() function, it is treated as TRUE. This is often unhelpful. To make blanks behave in a sensible way in calculations, you must first convert them to be "not available" using NA(). This function takes no inputs, and returns a missing value. To convert a blank value to a missing value, use this pattern. =IF(ISBLANK(cell), NA(), cell) Instruction In column H, use AND() to find women who have kids and get benefits. In column I, convert the blanks in column G to missing values. In column J, again find women who have kids and get benefits, this time using column I rather than G. please show the formula used to "has kids and gets benefits" , "gets benefits with missing values", has kids and gets benefits". Thank you Is non-white Has over 12 years of school? Is married? Has kids? Has young kids? Is head of household? Gets…
A voltmeter with an internal resistance of 100 KQ is used to measure the voltage Vab in the circuit shown below, what is the voltmeter reading? 36v R1-12 KQ M 30 18 mA R2=60 kQ R3=15 ΚΩ M + Vab Note: All students are welcomed to solve it, however assignments are mandatory for old students only.