The spring in the figure below is stretched from its equilibrium position at x = 0 to a positive coordinate xo. ko HINT x = 0 x = xo PE sn PE 50 The force on the spring is F and it stores elastic potential energy PESO. If the spring displacement is tripled to 3x, determine the ratio of the new force to the original force, and the ratio of the new to the original elastic potential energy, Fo Fo PESO (a) the ratio of the new force to the original force, PE ST PE SO (b) the ratio of the new to the original elastic potential energy,

The spring in the figure below is stretched from its equilibrium position at x = 0 to a positive coordinate xo. ko HINT x = 0 x = xo PE sn PE 50 The force on the spring is F and it stores elastic potential energy PESO. If the spring displacement is tripled to 3x, determine the ratio of the new force to the original force, and the ratio of the new to the original elastic potential energy, Fo Fo PESO (a) the ratio of the new force to the original force, PE ST PE SO (b) the ratio of the new to the original elastic potential energy,

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter1: Fundamentals Of C++ Programming

Section: Chapter Questions

Problem 2PP: (Conversion) An object’s polar moment of inertia, J, represents its resistance to twisting. For a...

See similar textbooks

Similar questions

A simple pendulum is formed of a rope of length L = 2.2 m and a bob of mass m. %3D When the pendulum makes an angle e 10° with the vertical, the speed of the %3D bob is 2 m/s. The angular speed, e', at the lowest position is equal to: (g = 10 m/s^2)
A simple pendulum of length L, has a maximum angular displacement e_max. At one point in its motion, its kinetic energy is K = 3 J and its potential energy is U = 4.2 J. When the pendulum's angular velocity is one-fourth its maximum value (0' = %3D O'_max/4), then its kinetic energy is:
Calculate the value of g and h in the following equation.
M D d T M. P- A circular shaft having diameters D and d and a groove of radius r (with M = 0 and P O) is made of steel with the allowable shear stress tall. Find the maximum torque I that can be transmitted by the shaft. Given: D = 28mm, d = 20mm, r = 4mm, and tall = 250 MPa. Please help with this question. The answer should be 157.1 Nm
20, Solve the equations Ax = b, where
The displacement of an oscillating spring can be described by x = A cos(wt) where x = displacement at time t, A = maximum displacement, w = angular frequency, which depends on the spring constant and the mass attached to the spring, and t = time. Find the displacement, x, with maximum displacement A of 4 cm, for times from 0 to 120 seconds with increments of 30 seconds, and angular frequencies from 0.4 to 0.6 radians/sec, with increments of 0.1 radians/sec. The displacement for all combinations of times and angular frequencies needs to be calculated. Use meshgrid. Display your results in a matrix with angular frequencies along the top row and times along the left column like so (you may put zero, 0, or NaN, in the upper left corner:
Q2/ The pipe in Fig. is driven by pressurized air in the tank. What is the friction factor (f) when the water flow rate through pipe is ( 85 m/hr ) and the pressure at point 1 is (2500 kPa). (25Marks) 30m smooth pipe d = 70mm open jet P1 1 90m 15m 60m
The flight of a model rocket can be modeled as follows. During the first 0.15 s the rocket is propelled upward by the rocket engine with a force of 16 N. The rocket then flies up while slowing down under the force of gravity. After it reaches the apex, the rocket starts to fall back down. When its downward velocity reaches 20 m/s, a parachute opens (assumed to open instantly), and the rocket continues to drop at a constant speed of 20 m/s until it hits the ground. Write a program that calculates and plots the speed and altitude of the rocket as a function of time during the flight. SOLVE WITH MATLAB PLEASE
The graph shows the temperature T, in degrees Fahrenheit, of molten glass t seconds after it is removed from a kiln. (0, 1500) 75 t (a) Find lim T. oF What does this limit represent? | This is the natural temperature of glass. This is the initial rate at which the glass is cooling. O This is the temperature of the kiln. This is the temperature of the room. (b) Find lim T. oF What does this limit represent? O This is the natural temperature of glass. This is the initial rate at which the glass is cooling. This is the temperature of the kiln. This is the temperature of the room.
Suppose that a parachutist with linear drag (m=50 kg, c=12.5kg/s) jumps from an airplane flying at an altitude of a kilometer with a horizontal velocity of 220 m/s relative to the ground. a) Write a system of four differential equations for x,y,vx=dx/dt and vy=dy/dt. b) If theinitial horizontal position is defined as x=0, use Euler’s methods with t=0.4 s to compute the jumper’s position over the first 40 s. c) Develop plots of y versus t and y versus x. Use the plot to graphically estimate when and where the jumper would hit the ground if the chute failed to open.
The electric flux density D at the point M (0,4,0) in the region about a uniform line charge of 1 nC/m lying along the z axis in free space is: Select one: a. None of the above b. 0.6366 nC/m c. 0.2387 nC/m d. 0.039 nC/m e. 0.1 nC/m
Q1/The pressure drop in pascals (Pa) for a fluid flowing in a pipe with a sudden decrease in diameter can be determined based on the loss of head equation given below: h = 24-11 2g Area A Area A Area A Where: V₂ is the velocity in position 2 (m/s), g: is acceleration due to gravity = 9.81 m/s², A₁ and A₂ are the cross-sectional areas of the tube in position 1 and 2 respectively. A==d² Where: d is the diameter (m). Write a program in a script file that calculates the head loss. When the script file is executed, it requests the user to input the velocity (V₂) in m/s and values of diameters (d, and d₂). The program displays the inputted value of v followed by a table with the values of diameters in the first and second columns and the corresponding values of h, in the third column. 2 2