Consider the following assembly program MOV CX, 1100H DLY: SUBS CX, CX, #1 NOP BNE DLY NXT: --- (a) How many times does the BNE DLY instruction get executed? (b) Change the first line of the program so that BNE DLY is executed 34 times (c) Change the second line of the program so that BNE DLY is executed 34 times, while the fist line stays unchanged (MOV CX, 1100H)

Consider the following assembly program MOV CX, 1100H DLY: SUBS CX, CX, #1 NOP BNE DLY NXT: --- (a) How many times does the BNE DLY instruction get executed? (b) Change the first line of the program so that BNE DLY is executed 34 times (c) Change the second line of the program so that BNE DLY is executed 34 times, while the fist line stays unchanged (MOV CX, 1100H)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
Which function performs the following operation? Give the assembly instruction and show your work.  Before A= 11011011, CF=1 After A= 10111101, CF=1
1- Write a program in assembly language to perform the following logic ci CL DL [5100]– 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX, FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX,
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
P. 2. Consider a proposed new instruction named rpt. This instruction combines a loop's condition check and counter decrement into a single instruction. For example rpt x29, loop would do the following: if (x29 >0) { x29 = x29 -1: goto loop a) If this instruction were to be added to the RISC-V instruction set. what is the most appropriate instruction format? b) What is the shortest sequence of RISC-V instructions that performs the same operation?
Please show work included 6. Assume a digital to analog conversion system uses a 7-bit integer to represent an analog temperature over a range of -27oF to 100oF. If the actual temperature being read was 40oF, what would be the closest possible value that the system could represent? Write the answer in a 7-bit binary number as well as in decimal. The answer should be in the following form 00010001 and -10oF a set of two numbers.
1- Write a program in assembly language to perform the following logic ci D- CL DL [5100]– 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL, 00 MOV BX, FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX, 就
2. Consider the following circuit D å lå a. Find the expressions for D, T, Qo*, Q₁*. b. Write the transition output table. c. Draw the state diagram of the circuit. d. Is this a Mealy or Moore machine? Explain. T 21 a la 1
a) In Assembly programming what is the functionality of the following instructions DECFSZ ВTESC MOVLW MOVWF goto b) A piece of code is required for a time critical activity. Should this be written in assembly language or C? Explain your answer. 5 Explain the difference between the (For) and (While) loops. Highlight the main components of the (For) loop that are required for its execution. Consider the following C program designed to run on a PIC 18F4455. int main(void) 2 { 1 double voltage; double current; double milliwatts; double energyUsed; double cummulativeEnergy = 0; while (1) { voltage=analogRead (VOLTAGE_PIN)*voltageScaleFactor; current=analogRead (CURRENT_PIN)*currentScaleFactor; milliwatts=voltage*current; energyUsed=milliWatts*0.5; cummulativeEnergy=cummulativeEnergy+energyUsed; 10 11 12 13 14 15 _delay_ms (500); 16 } 17 a) What is the role of the symbols "{" and "}" b) The code here is indented. Explain the importance of indentation N m 4 n Or 00 o A m
Part 1:Compile the assembly code for the following C code. Part 2: What is the process for calculating the total number of RISC-V instructions needed to execute the function? Can you find an exact solution? If so, what is that? If not, why not?