consider a flow of water in a cylinder maintained at constant temperature of hundred degree Celsius the diameter of the cylinder is 15 and the length of the tube is 6 metre the inlet and outlet temperature of the water is TI equal to 15 degree Celsius and equal 57 degrees celsius find the average heat transfer Coefficient associated with the flow of water mass flow rate is

consider a flow of water in a cylinder maintained at constant temperature of hundred degree Celsius the diameter of the cylinder is 15 and the length of the tube is 6 metre the inlet and outlet temperature of the water is TI equal to 15 degree Celsius and equal 57 degrees celsius find the average heat transfer Coefficient associated with the flow of water mass flow rate is

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Similar questions

A thick-walled cylinder tubing of hard rubber having an inside radius of 20mm is being used as temporary cooling coil in a bath. Ice water is flowing rapidly through inside tube and the inside wall temperature is 274.9K. The outside surface temperature is 297.1K. A total of 14.65W must be removed from the bath by cooling coil. How many m of tubing are required?
Hot fluid "C 2562 J/kg.k, Pr 51.3, u-5.22E-3 Pa.s, k0.260 Wm.K" flows af 0.8 kg/min inside a 3-mm diameter, thin walled tube. The tube is coiled and submerged in a water bath maintained at 23 C. The fluid experiences a temperature drop of 63°C and leaves the tube at 35 C. What is the required lengih of the tube "m Neglect heat transfer enhancement associated with the coiling. Assume ftlly developed flow, If turbulent flow use Dittus Boelter equation: Nn 0.023 Re Pr
YOuTube Çevir Omail S Community Downl... A Haritalar Okuma listesi iş İÇİN Giriş yap 口4 INGİLİZCE Cold water entering an opposing flow heat exchanger at a flow rate of 0.6 kg/s at 20 oC (cp =4180 J/kg.K) with a flow rate of 0.75 kg/s of oil (cp 2200 J/kg.K) it is used for cooling from 110 OC to 85 oC. If the total heat transfer coefficient is 800 W/m2.lf K, What is the heat transfer area of the heat exchanger? Çeviri yap: Google Bing
Water at a temperature of 20 oC with a mass flow rate of 0.015 kg/s enters the pipe 2.5 cm in diameter with a uniform surface temperature of 90 oC. a) Determine the length of the thermal inlet region, Lt.b) If it is assumed that the flow is hydrodynamically and thermally formed, calculate the convection heat transfer coefficient and the length of the pipe required to heat the water to 70 oC.c) What is the rate of heat transfer to the water?d) Calculate the friction factor and pressure drop.
Water is flowing through 40-mm diameter 4-m long tube with a rate of 2kg/s. Tube surface temperature is maintained at 100 oC and the water enters the tube at 27oC. a) What is the outlet temperature of the water? b) What is the corresponding heat transfer rate?
Please with proper solution. Thanks An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps against a condensing temperature of 40°C. For the two different evaporating temperatures of +10 °C, compute the refrigerant flow rate in kg/s assuming that the clearance volumetric efficiency applies.
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
a)Identifythe maximum velocitylimitof ammonia gas in the pipe if the flow is to be maintained as laminar flow. b)If the actual velocity of ammonia gas is 0.9 times the maximum velocitylimit, calculatethe heat transfer coefficient and heat transfer flux if the heat transfer area is 0.16m^2. c)Suppose the pipe has an outer diameter of 43.1 mm and the outer surface wall temperature of the pipe is 356 K, determinethe thermal resistance and thermal conductivity of the pipe.
48. Water is flowing in a smooth pipe of diameter D. A section of this pipe hav- ing a length of L is heated. Water at the inlet to the heated section has a tempera- ture of Tŋ. Water temperature at the exit of the heated section is Tp. The heated section of the pipe wall is maintained at a constant heat flux so that a constant temperature difference of AT, = T, – T, exists between the wall and the bulk wa- ter temperature. Show that for turbulent flow in the pipe and a specified heated length and pipe diameter, water temperature at the exit of the heated section is given by: 402 0.6 Pr T52 =Tf +0.0876 L AT DO.8 0.2 m
Design a hydrocooling unit to cool down fruits and vegetables from 30 °C to 5 °C in 20 minutes at a rate of 20,000 kg of fruit or vegetables/h. The design must fulfill the following requirements: The unit will be an immersion flooded system. It must be able to cool down and transport the products in chill water. The tank has the following dimensions approximate. three meters wide and up to 90 cm hight. The water will circulate and be cooled through the evaporation section of a refrigeration system. The refrigerant temperature inside the coils will be -2 °C, and the water temperature must not drop below 1 °C and must not exceed 6 °C. Assuming reasonable values for the average density, specific heat, and porosity of the product (the fraction of the volume of air in a box), recommend reasonable values for: The speed of the water through the canal, the capacity of the cooling system. the compressor power.
For an exhaust valve, the mass flow rate through the valve is 1.26 kg/s. The flow coefficient is 0.65 and the cylinder pressure and temperature are 625 kPa and 820 K. Assume exhaust system pressure is 103 kPa, the specific heat ratio is 1.4 and R =287J/ kg.K. The effective area of the valve is (SI unit): Select one: O a. 3.45*10-2 O b. 0.85*10-2 O c. 2.2*10-3 O d. 1.85*10-3 O e. 1.42*10-3
(heat transfer ) thanks The velocity of the fluid flowing in parallel over a 500mmx500mm flat heater surface is U= 19 m/s and the inlet velocity temperature is T_∞15 C. The surface temperature of this plate is T_s140 C, the friction force is F_D=0.4 N and the surface area of the plate is A=0.32 m2. According to this;(F_D= 0.4N A=32 m2)a) Surface shear stressb) Find the coefficient of frictionc) Heat transfer coefficientd) What is the amount of heat transfer (electric power) that must be given to maintain a constant surface temperature?