Read the question carefully and give me right solution according to the question. Consider a car modeled as shown below with a mass m = 1100 kg, suspension stiffnessof 400 kN/m and suspension damping coefficient of 15 kN.s/m. The vehicle is travelingto the right and hits a step in the road of height a =0.03 m. Derive the resulting responseof the car and calculate the maximum displacement as well as steady statedisplacement. Assume that the wheel of the car follows the step perfectly andinstantaneously.mja = 0.03 m

When the steady-state has reached and the displacement is less than that of the base and it is…

Answered: Consider a car modeled as shown below…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simple 1-DOF model of a vehicle suspension is shown in the figure below (a). The vehicle is traveling over a rough road at a constant horizontal speed. Assume that the road contour is sinusoidal as shown in the figure below (b). The mass of the vehicle is 900kg. The stiffness of the suspension is 8x10*N/m and the system shock absorber providing a damping ratio of 0.2. Determine the acceleration and displacement amplitudes of the vehicle body when the horizontal velocity is 40m/s. Plot the displacement amplitude and the acceleration amplitude as functions of the vehicle speed. (due 8:20PM) (a) -- 16m 4-10 m 32 e (m) (A)
A horizontal beam ABC is loaded as shown in the figure below. The distance, of the point of contra flexure from end A (in m) is
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800lb, f ind the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise. Solve Prob. 7.60 if the drum is rotating counterclockwise.
For figure shown, determine the vertical component of the given force in Newton that lifts the car off the ground of the the truck
The tank shown rolls along a level track. Water received from a jet is retained in the tank. The tank is to accelerate from rest toward the right with constant acceleration a. Neglect wind and rolling resistance. Find an algebraic expression for the force (as a function of time) required to maintain the tank acceleration at constant a. initial mass of cart and water, Mo F U
A vertical one-link manipulator is illustrated in Figure Q1b. Assume that there is viscous friction at joint 0, determine the dynamic model of this manipulator through Newton-Euler approach. mg Coefficient of Friction, u Figure Q1b
7= fart Q1. Given the eulerian-vector field V= 4x?i - 10x2yj + 2tk find the velocity and the resultant acceleration at ( 2, 1, 3) at time t= 1
A string is wrapped around the hub of the spool. a pull at the end of the string causes the spool to roll on the horizontal plane without slipping. At a certain instant, the angular velocity and angular acceleration of the spool are as shown in the figure. For this instant, find (a) the acceleration of the point D on the spool; (b) the acceleration of point B ; and (c) the acceleration a0 of the end of the string.
A 200-lb block is sliding along a horizontal plane at 4 ft/s when a force P is applied on it as shown. The magnitude of P varies according to the relation P = 200t lb where t is in sec. Find the velocity of the block 2 sec after P is applied. Neglect friction. Use Impulse-Momentum Method and draw the momenta and impulse vectors.
The figure shows a helicopter with a three-dimensional geometry. During a ground test, an aerodynamic force of 400 N acts on the tail rotor at P as shown in the figure. Calculate the component of this force on the z-axis of the moment of the helicopter relative to O point by vector operation.
A SDOF portal frame fixed at its base has a mass of 1,300 kg at roof level. Lateral stiffness of frame columns together is 27,000 N/m. The initial displacement of the mass from its equilibrium position was 15 mm and the initial velocity was 17mm/s. After how many seconds since the release of the initial displacement (after t = 0) will the mass first reach its peak displacement? Note: Get the value of t without using the formula for maximum response u0, instead use a calculus method.
The cantilever steel beam as shown below has the rectangular cross section shown, determine the maximum displacement of the beam use E=200 GPa for the modulus of elasticity 200mm 4 KN/m 6 KN .m 350mm 2m 2m 1m

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS