When a fluid supply system is subjected to a linear rigid body motion with constant linear acceleration a along a distance L, the modified Bernoulli Equation takes the form: P V + g21 P V + gz, = aAL + Losses 2 where V and V½ are velocities relative to a fixed point and 'Losses' which represent frictional losses are zero when the frictional effects are negligible. The tank with two discharge pipes (one is vertical and the other is inclined) shown in Figure Q4 below accelerates to the left at a constant linear acceleration of 3 m/s². If volumetric flow rates from the both pipes are to be identical, determine the diameter D of the inclined pipe.

When a fluid supply system is subjected to a linear rigid body motion with constant linear acceleration a along a distance L, the modified Bernoulli Equation takes the form: P V + g21 P V + gz, = aAL + Losses 2 where V and V½ are velocities relative to a fixed point and 'Losses' which represent frictional losses are zero when the frictional effects are negligible. The tank with two discharge pipes (one is vertical and the other is inclined) shown in Figure Q4 below accelerates to the left at a constant linear acceleration of 3 m/s². If volumetric flow rates from the both pipes are to be identical, determine the diameter D of the inclined pipe.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An inverted differential manometer is connected to two pipes A and B whichconvey water. The fluid in manometer is oil of specific gravity of 0.8. For themanometer readings r = 30 cm, s = 20 cm and t = 30 cm, find the pressuredifference between A and B.
6/47 A block of mass mo is placed between the vertical wall and the upper end A of the uniform slender bar of mass m. If the coefficient of static friction is µg be- tween the block and the wall and also between the block and the bar, determine a general expression for the minimum value 0min Oof the angle 0 for which the block will remain in equilibrium. Evaluate your expression for the conditions µ = 0.5 and %3D т (a) mo 0.1, m (b) mo 1, and m (c) mo 10. %3D For each case, state the minimum coefficient of sta- tic friction (u)B necessary to prevent slippage at B. Ans. (a) 0min = 61.2°, (µ,)B = 1.667 (unusual!) (b) 0min = 45°, (µ)B = 0.667 (c) 0min = 10.30°, (µ,)B = 0.0952 %3D %3D %3D %3D %3D mo m (Ha)B Problem 6/47
In the illustration: A 1 B 2 D All friction factor f = 0.02 All pipe lengths L- 250m Diameter of Pipe A = 400mm with Flow Rate at Pipe A = 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C= 200mm Diameter of Pipe D = 400mm Solve for - Headloss in meters at Pipe A.
PROBLEM 3 A nozzle discharges 2 cfs with a velocity of 50 ft/sec. The nozzle is inclined downward so that as the water jet strikes a fixed curved vane it is directed 30° down from the horizontal. The jet is deflected upward 90°, making an angle of 60° with the horizontal as it leaves the vane. Determine the x- and y-components of the force exerted by the water jet. Express the answers in pounds.
In the illustration: A В 2 D All friction factor f - 0.02 All pipe lengths L- 250m Diameter of Pipe A= 400mm with Flow Rate at Pipe A = 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Diameter of Pipe D = 400mm Solve for - difference in elevation in meters in between reservoirs.
An incompressible fluid is flowing at a steady rate in a horizontal pipe. From a section, the pipe divides into two horizontal parallel pipes of diameters di and d2 (where d₁ = 4d₂) that run for a distance of L each and then again join back to a pipe of the original size. For both the parallel pipes, assume the head loss due to friction only and the Darcy-Weisbach friction factor to be the same. The velocity ratio between the bigger and the smaller branched pipes is
Q1:-Answer the following statements with (True) or (False). only) 1- Bernoulli's equation is an energy principle of Non-viscous and head losses are consider it. 2- Pgz is the hydrostatic pressure, which is not pressure in a real sense since its value depended on the reference level selected. 3- The disparity between the theoretical discharge velocity and the theoretically discharge as the coefficient of velocity. 4- When the coefficient of contraction of positive relationship with coefficient of discharge. 5- The objectives flow measuring by orifice meter is determining the velocity coefficients only. 6- Losses in Bernoulli test depend on the nature of the material made.
The velocity potential function for a source varies as A B C D log
For the following equilibrium system, assuming all strings are ideal. If the mass M = 50, and the angles B and 0 are 50 ° and 30, respectively. What is the value of the magrnitude of the voltage T4? a) T = 762.3042 N b) T = 980 N c) T, = 565.8035 N d) T=639.6499 N
Problem 5. Calculate the maximum safe magnitude of M considering the following data and figure shown below. Assume that the mass M is a rigid platform. M E (GPa) A (mm²) а, (МPа) Copper 120 1000 80 Steel 200 1200 160 +1.0 m→|<1.0 m→|
For a two dimensional potential flow, the velocity potential is given by, O = x(2y-1) The value of stream function Y at the point P(4, 5) is units if stream function Y is zero at (0, 0).
26. A block with a mass m is placed on the top of an identical block m and the system of two blocks is at rest on a rough horizontal surface as shown below. The top block is tied to the wall. The coefficient of static friction between all surfaces is us. What maximum value does force F reach before the lower block starts sliding to the left? * F m e. 4 psmg c. 4 usmg d. ½ psmg a. 3 psmg O b. 2 psmg