Compute the following values for each item. Write your answers on a clean sheet of paper. <1. Calculate the frequency of this low-pass filter given a resistor value of 1.2kn and a capacitor value of 4.7μF. 2. Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 250Hz and a higher cut-off frequency of 1.2kHz. Find its center frequency, bandwidth and Q of the circuit assuming the capacitor for both filter sections is 0.1uF.

Compute the following values for each item. Write your answers on a clean sheet of paper. <1. Calculate the frequency of this low-pass filter given a resistor value of 1.2kn and a capacitor value of 4.7μF. 2. Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 250Hz and a higher cut-off frequency of 1.2kHz. Find its center frequency, bandwidth and Q of the circuit assuming the capacitor for both filter sections is 0.1uF.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A signal with bandwidth 100HZ is over sampled by 40% then the cutoff frequency of the low pass reconstruction filter to recover this signal is. fc= Hz
A high-pass filter is to be designed for speech signal processing. The cutoff frequency is 3.4kHz and the gain to be 10.0 in the passband. At 340Hz, the gain is desired to be less than or equal to 0.1% of the gain at 3.4kHz. Please use Sallen-Key type of filters for this design and draw the complete circuit schematic and indicate the resistance and capacitance values.
Describe the possibility of building a second order filter with only resistors and capacitors? and design the cutoff frequency of second order filter for low pass filter. (Expected: Describe the possibility, design the second order filter for low pass filter circuit and design the cutoff frequency as equation only).
Suppose that we want a first-order high pass filter that has a transfer function magnitude of -15 dB at f = 50 Hz. Find the break frequency for this filter. O f.=100 Hz %3D Of =281 Hz %3D O f,=75 Hz %3D Of,=512 Hz B.
5. Why we use semiology paper to draw the frequency response of filters. 6. What is filter order, and what is the effect of changing filter order on the filter response and complexity of filter. 7 Sketch the frequency response of low-pass, band-pass, high-pass, and band-reject filters.
Design and sketch the block diagram of the receiver that will recover signals, m, (t) and m(t) from the modulated signal c(t). Specify the type and the cutoff frequency for every filter you use in your design, give the specifications for any other component you might use. Write all design parametrs on the receiver.
1. A) B) Write the transfer function for the RC high-pass filter of Figure 2. First write it in terms of jw (or s) and then write it as its magnitude and phase angle. Determine and record below the cutoff frequencies of the circuit. wwwwww Sketch the straight line approximations of the frequency responses for the RC high-pass filter on Graph Av0.1 0 -10 -20 90° 60* 30° 0⁰ -30° -60° -90° e-2 sin (et) 0.1 0.2 (a) Voltage gain response 0,5 0.2 (b) Phase shift response 0.5 1 C = 0.47 uF R-330 ohms 2 ww 5 10 10 Vout 20 20 50 50 100 f (kHz) 100 (kHz)
(a) The gain of a bandpass filter at its lower cutoff frequency is 12. The upper cutoff frequency is 11.2 kHz and the Q is 30. Determine: () The gain at the centre frequency (ii) The centre frequency (ii) The bandwidth (b) The input to the filter in (a) has the following components: Vi1: 2V rms at 2 kHz and Vi2: SV rms at 20 KH2 Determine the rms values of these components in the filter's output.
The output of a limiter is a signal: Select one: O Constant O Triangular O Sinusoidal O Square Bandpass limiter in FM receiver is used to: Select one: O a. amplify the received signal b. demodulate the received signal C. approximate the differentiator Od. remove the amplitude variation in the received signal
Write Legibly. Design a single pole low pass filter with a gain of 10 in the passband and a 3dB frequency of 5kHz. The minimum resistance in the passband for this filter is to be of 10k-ohms. What is the value of C in nF and in two decimal places only.?
4) Compare the response of first order, second order and third order filters.
Derive an expression for the cut off frequency of a low pass RC filter