To approveD.Compressive stress can be defined or described as an internal force in a matefa26.resisting aA. shearing load.B. pulling load.C. pulling and shearing load.D. pushing load.27.The following material is being order as the most hardiness material.A. Glass, Lead, Aluminum, Gray ironB. Gray iron, Aluminum, Glass, LeadC. Aluminum, Gray iron, Glass, LeadD. Glass, Grày iron, Aluminum, Lead28.The edges of a cast iron block weighing 32 kg were rounded off with a mil uthe block was reweighed, it was found to weigh only 29.5 kg. What percentage oforiginal cast iron block was lost?A.7.8%8.5%4%D. 2.5%В.С.oil vve

Note: As per the Bartleby guidelines, only one question can be answered at a time. Therefore, please…

Answered: Compressive stress can be defined or…

Compressive stress can be defined or described as an internal force in a mate 26. resisting a ... A. shearing load. B. pulling load. C. pulling and shearing load. D. pushing load.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

26. Compressive stress can be defined or described as an internal force in a material resisting a ... A. shearing load. B. pulling load. C. pulling and shearing load. D. pushing load. 27. The following material is being order as the most hardiness material. A. Glass, Lead, Aluminum, Gray iron B. Gray iron, Aluminum, Glass, Lead C. Aluminum, Gray iron, Glass, Lead D. Glass, Gray iron, Aluminum, Lead
Millimeter 17. Which part of the marking gauge is used to mark lines on wood? To measure the ductility of weld metal b. To test the skill of a welder To perform a non-destructive test d. To approve welds to certain standards a. C. 18. Compressive stress can be defined or described 2s an internal force in a material resisting a. a pulling load. b. shearing load. pulling and shearing load. d. pushing.load. • C. 19. Which plane more suitable for further smoothing a planed surface? Router plane. b. Trying plane. c. Smoothing plane. a. 20. Which one of the following is gives the name of the screw? a. Siot. b. Thread. Head. d. Shank. C. 21. How to hold the hammer handle while driving the naii? Middle of the handle. * b. Anywhere in length of the handle. C. Near the hammer head of the handle. End of the handle a. USF ال لجنة العلمية d. File is
34. Stress is given by the following formula: (choose correct sentences) a. 8 = # b. 8 === c. 8 = Ex d. 8 = _applied force cross section area 35.Types of cast iron are: a. Low cast iron, Medium cast iron and High cast iron b. Gray, White, Malleable and Ductile c. Low-carbon, Medium-Carbon and High-Carbon d. Black, Gray and White
2) Which one of the following material is having high toughness a. High carbon steel b. Medium carbon steel c. Ductile cast iron d. White cast iron
15- Which one of the following material is having high toughness a. High carbon steel b. Ductile cast iron c. Medium carbon steel d. White cast iron
20- Vickers Hardness Number (HV) value is directly proportional to a. Shape of indenter b. Indentation mean diagonal c. All of the above d. Force applied
32. Fine-grained materials have stress-hardening properties. a. True b. False
_____ is an example for indirect stress Select one: a. Shear b. Bending c. Tensile d. Compression
For the following inspection opening, calculate the correct values for A, A1, A2, A3, A4, A5 The design pressure is 900 kPa.g and the design strengths for the metals of shell and branch are 133MPa A= a. 3545.24 b. 3354.63 c. 3454.36 d. 3445.42 A1= a. 1377.45 b. 1673.71 c. 1773.82 d. 1534.53 A2= a. 721.63 b. 733.32 c. 718.59 d. 738.93 A3 = a. 600 b. 500 c. 450 d. 550 A4 = a. 211 b. 214 c. 220 d. 216 A5= a. 346 b. 356 C. 366 d. 336
Any steel used as a tool may be technically classified as a tool steel. However, the term "tool steel" is usually restricted to high-quality specialty steels used for cutting or forming purposes. True False Both Ferritic and Martensitic stainless steels belong to the AISI 400 series. Ferritic stainless steels are heat-treatable grades and martensitic stainless steels can only be strain hardened to improve their mechanical properties. True False The RIM (Reaction Injection Molding) process does not require the plastic materials to be heated before molding. True False An aluminum alloy designated as 3003-H16 aluminum means the following: 3XXX aluminum-manganese alloy, which has not been modified, specific alloy 03 in the alloy series, strain hardened only, with a 3/4 hard temper. True False Titanium is extensively used for jet engine components (rotors, fins, and compressor parts) and other aerospace parts because it is as strong as aluminum and 45 percent…
Please match Heat-Treated Steels with their hardness HB numbers, according to the charts shown below. a) SAE 1040 WQT at different Temperatures b) SAE 4140 OQT at different Temperatures c) SAE 4340 OQT at different Temperatures SAE 1040 WQT 1000 SAE 4140 OQT 1000 SAE 4140 OQT 1100 SAE 4340 OQT 800 a. HB = 415 b. HB = 341 c. HB = 311 d. HB = 269
Stainless steel 18. These are used in wide variety of applications owing to the properties like good fluidity, ease of casting, low shrinkage, excellent machinability, wear resistance and damping capacity. * O Cast irons Copper alloys O silver alloys O Steels 16. The condition after more than 500 years. tubing used in water plumbing in pyramids was found in serviceable