What is the springs free length(ft)?

Q: Define Locked in loads

A: Load  - A load is a mechanical stress , moment or couple that a mechanical body is subjected to…

Q: Conclusion about Hooke's Law

A: To conclude that what Hooke's Law state

Q: a) Differentiate axial load and eccentric load b) Explain the limit of eccentricity.

A:

Q: Go Cylinder A - Steel |Cylinder B -Aluminium 350 mm 500 mm IX

A: Given,  composite rod  da= 40  mm , la = 350 mm db= 50 mm , lb = 500 mm

Q: What would be the stretched length in spring (AB)?

A:

Q: What happens if the torsional loadings applied to the shaft?

A: When the torsional load is applied on the shaft, the shear stress is produced in the shaft, and this…

Q: For what purpose is a torsion test performed?

A: The torsion test is used to determine the shear properties of the material. In this testing, the…

Q: 3. where used the heli cu we springs

A: The helical spring, in which wire is enclosed by a loop that takes after a screw string, is…

Q: least factor of safety if the material is cold-d

A: Sfhh

Q: What is referred to as the torsion formula?

A: Let us consider a shaft subject to the torque at the free end and fixed at the other end.

Q: Conclusion about Hooke's Law of Spring

A: To conclude about Hooke's Law of Spring

Q: Two springs are at

A: OPTION d)0.20m/s

Q: How does the element of material deforms?

A: elements of a material are deformed when some external force is applied to it.

Q: What is the Constant Load and Cross-Sectional Area?

A: Load: The load is a force that caused the stresses, deformation, and acceleration in the bodies.…

Q: What is the Flexure Formula?

A: The stresses in the beam caused by the bending moment is called as flexural or bending stress.

Q: specification required for the bolt

A: Given; Three bolt system as shown in figure;The bolt material has ,shear yield…

Q: What happens if the load on an actual column exceeds its critical loading?

A: There are two types of the column, 1. Short Column 2. Long Column The slenderness ratio and length…

Q: What happens when the member is confined?

A: Confined member: If a member is confined then it means it is fixed to a position.

Q: While discussing types of coil springs: Technician A says that linear-rate coil springs have equal…

A: Technician A:- Technician A is correct says that in case of linear-rated coil springs have equal…

Q: What is the maximum deflection?

A: Given Beam To find Definition of maximum deflection

Q: Which of the following is the permissible working stress in psi of UNC bolts that has a stress area…

A: Given Data: Stress area of the bolt, A=0.4 in2

Q: change in spring stiffness is?

A: Given: If the wire diameter of a compressive helical springs is increased by 2%,We have to find then…

Q: What is the cause of slipping inductile failure?

A: Causes of slipping in ductile failure are as follows

Q: What are the short columns?

A: The short column is the column when the length of the column is less than as compared to lateral…

Q: Describe how to test for equilibrium of masses ?

A: Let us discuss about  equilibrium of masses and criteria when it is in equilibrium condition.

Q: What is the Falling Block?

A: Falling block: The falling block is an action in which a solid metal slides vertically in a grove…

Q: What is the equivalent stiffness of the springs in the system?

A: Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: What is the thickness of steel?

A: To find thickness of steel.

Q: bolts required for an

A:

Q: Which members are made of composite materials?

A: Reinforced concrete and masonry. Composite wood such as plywood. Reinforced plastics, such as…

Q: what is the part of the spring being compressedor stretched upon application of force

A: When the force (tensile or compressive) is applied the spring either get elongated or gets…

Q: How mary MI4 10.9 bolts used in Vith &s Systen ?

A: ANSWER- 5 BOLTS

Q: What is damping factor?

A: Damping factor is a ratio used in the study of vibration of a system which has kinetic friction. It…

Q: erence between a point loa

A: Difference between point load  and distributed load

Q: what is the sizes of thr fins screw?

A: Solution:   The basic size of a single fin screw is given below:

Q: The maximum radial load

A: Given: The dynamic load capacity of 6306 bearing is 22 KNMaximum radial load it can sustain to…

Q: What is the internal axial force in a member?

A: Whenever any load applied on a member the material of the object opposes its action in the opposite…

Q: A ball and a socket joint forms a

A: A ball and a socket joint is a form of synovial joint in which socket swivel around the fixed ball.…

Q: l the spring be compressed?

A: x= 13.717cm

Q: rigid flange coupling

A: Mt=228 Nm=228000Nmm Diameter of shaft τ=16Mtπd3100=16*228000πd3d=22.645 mm or 25 mm

Q: Determine the number of prismatic joints

A: 1. Option (c) 1  is correct option  Explanation: The slider pair is called prismatic pair. Because…

Q: made of steel with elasti d with the help of free be

A: Diameter of bolt, d=10 mm,Cross section of rectangular plate, A=12 mm× 7 mmTension in the bolt,…

Q: 2. List any four reasons why factor of safety is necessary while choosing the material.

A: The factor of safety is defined in the following two ways: For the ductile materials, the factor of…

Q: Describe uncontrolled spring action without a shock absorber.

A: Function of shock absorber:  A shock absorber is also known as damper. it is a mechanical device…

Q: ht, what is the tension in the wire?

A: To find tension ( T)