: Choose the correct answer for the following (n 1. instructions is not valid. a. MOV DS, 3000H b. РОP СХ c. DAA 2. When the word is to be popped from the top of the stack, the value of stack pointer is ... a. incremented by 1 b. incremented by 2 c. decremented by 2 3. A microprocessor has Data Bus a. unidirectional b. bi-directional c. Both 4. A microprocessor requires .... power supply. a. +10V b. +7V c. +5V 5. ... instruction is not conditional jump instruction a. JA b. JMP c. JE

: Choose the correct answer for the following (n 1. instructions is not valid. a. MOV DS, 3000H b. РОP СХ c. DAA 2. When the word is to be popped from the top of the stack, the value of stack pointer is ... a. incremented by 1 b. incremented by 2 c. decremented by 2 3. A microprocessor has Data Bus a. unidirectional b. bi-directional c. Both 4. A microprocessor requires .... power supply. a. +10V b. +7V c. +5V 5. ... instruction is not conditional jump instruction a. JA b. JMP c. JE

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The microprocessor unit that responsible for instruction queuing is .. O EU O ALU BIU O Segment registers O None of the above
(B)- Choose the correct answer for the following questions (Choose FIVE Only) 1. Assume AL register 7FH, it would become... after executed NEG AL instruction. a. 8FH b. 18H с. 81н 2. The unknown value for ????:B000H=25000H physical address is a. 001A H b. 1A00H c. 100AH 3. A microprocessor has ..... address bus a. unidirectional b. bi-directional c. Both 4. Instruction queue allows up to ........ of instruction code to be pre-fetched. a. 16 bits b. 6 bytes c. 6 bits 5. To activate the address bus or data bus in ADo-AD15 signal the .. should be either logic 1 or 0. a. MN /ΜX b. RD c. ALE 6. According to Moor's Law...... a. number of transistors on b. number of transistors on c. number of transistors on an integrated circuit an integrated circuit tripled an integrated circuit not doubles every two years every two years change.
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
Q5: Fill in the following blanks with appropriate answers (Choose Five Only) 1. The instruction that subtracts 1 from the contents of the specified register/memory location is ..…….….…..………………….. 2. In general, the destination operand of an instruction can be ....... 3. The instruction that supports addition when carry exists is 4. If there is a carry from lowest nibble during addition, ............. flag sets. 5. register is used as a default counter in case of string and loop instructions. 6. In PUSH instruction, after each execution of the instruction, the stack pointer is. ************** **********
4) Design and draw these memory units with their control circuits. Explain operations. a) A single EPROM 2716 is used with an 8088 microprocessor so that this microprocessor will see only X bytes of memory between the address range of DF800 –DFFFF or DD800 - DDFFF instead of 1M byte that it expects. Draw this circuit. What are X bytes? Do not use 74138 decoders. b) Design and show a 16K x 16-bit memory circuit by using 8K x 8-bit RAMS. Explain its operation. Do not use decoder 74138 chip.
Problem #4: Consider the Programmable Array Logic PAL module below '1' A B C D F₁ F2 F3 1. Determine the corresponding product term per row PRODUCT TERMS 000000
2) Convert Hexa-decimal to Octal a. 7E6A(16)=?(8) b. C350(16)=?(8) c. 9E36.7A(16)=?(8) d. EADD.EBEF(16)-?(8)
4. Write a simple complete program with LOOP instruction for 8086 microprocessor, and explain the processes for each line of the program.
Explain the function of Multiplexer and, Draw the 2 x 1 multiplexer logic circuit diagram and function table. How many selection inputs are required for a 4096 x 1 Multiplexer?
Sketch a circuit to represent the logic AB’C’D using a. a conventional symbol b. an array logic symbol.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Q1// What are the difference between Logic Devices and Programmable Logic Devices? Q2// Explain the advantage's of Programmable Logic Devices? Q3// List the disadvantages of Fixed function logic devices. Q4// Compare between Logic Devices and Programmable Logic Devices?