Title : memory location question: The following word contents are found in consecutive locations of memory: memory location question: The following word contents are found in consecutive locations of memory: Address Contents 00101A F0CE 00101C 3BAB ? 07FC ? B760 ? 2FB3 Fill in the missing addresses. 2)What is the value of the 32-bit number at address 00101C? plz explain why? 3)What are the byte contents at address 001021?plz explain why? 4)What are the contents of the MSB of the 16-bit number at address 001020?plz explain why

Title : memory location question: The following word contents are found in consecutive locations of memory: memory location question: The following word contents are found in consecutive locations of memory: Address Contents 00101A F0CE 00101C 3BAB ? 07FC ? B760 ? 2FB3 Fill in the missing addresses. 2)What is the value of the 32-bit number at address 00101C? plz explain why? 3)What are the byte contents at address 001021?plz explain why? 4)What are the contents of the MSB of the 16-bit number at address 001020?plz explain why

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

6- Set BX to 4567H, CX to FEDCH and SP to A59FH, then run the instructions: PUSH BX PUSH CX a. What is the new value of SP ? b. Display the memory locations where you pushed the values of BX and CX in the stack.
Assume that memory location $c100 holds a data byte =$37, [ACCA]= $B8 and [ACCB]=$FE. For each of the following instructions determine the resultant content of ACCA or ACCB. (a) ANDA $C100 (b) ANDA #$05 ORAB #$EE (c) (d) CLR B (e) NEGA (f) DECB (g) ASLA (h) LSRB (i) EORA #$E4 (G) ROR A
question1:In a memory system, data is 16-bit wide. Break the information into bytes with their addresses using little endian and big-endian methods. Starting address is F800 and the data is: E0F2 0041 question2:What acknowledgment signals are there in I2C bus?
Write a program to add the following five data bytes stored in memory locations starting from XX60H, and display the sum. (The sum does not generate a carry. Use register pair DE as a memory pointer to transfer a byte from memory into a register.) Make a flow chart for the same. Data(H) 1A, 32, 4F, 12, 27
Question 1: Use Indirect addressing to write a PIC24 assembly code that complements and adds 5 and multiply by 2 to 1024 data bytes into the memory at starting address Ox1000. The original data are stored in the memory starting from address 0x800. it is an electrical engineering question . this is the full information about the question!
MICROPROCESSORS Name: Class: Attempt all questions Q1/ Fill blanks HOMEWORK-5 ************************ 1. 2. is a group of 20-bit (A0-A19). These lines are 3. is a group of 16 lines. These lines are 4. contains lines that select the memory or I/O and cause them to operation. perform or 5. The micro-architecture of the 8086 microprocessors employs processing 6. The 8086 CPU is divided into two independent functional units:- and-- 7. is responsible for decoding and executing instructions. consists of and 8. is responsible for performing all external bus operations. 9. The BIU uses a mechanism known as an to implement a pipelined. 10. is 16 bits in length and identifies the next word of instruction code to be fetched from the current code segment. 11. contains the offset of the instruction code instead of its actual address. 12. the 8086 has four general-purpose data registers are -and- 13.--- -----are store offset addresses. 14.if CS = 1B6CH and IP = AOH, the microprocessor fetches its…
1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?
Write a program to PUSH R0, R1, and R3 of Bank 0 onto the stack and POP them back into R5, R6, and R7 of Bank 3. Also, mention the value of SP register after every PUSH and POP operation. this question is asked in microprocessor and microcontroller
If the current value of the stack segment register and stack pointer are C00016 and F F0016, respectively, what is the address of the current top of the stack ?
1.Show the status of PSW (Program status word) after addition of two 8bit numbers 26H and 3FH. Also draw status of flag register with help of diagram? 2. Mention the addressing mode, function and how many bytes instruction for the following instructions? ADI 42H b. LXI H, 2500H c. RLC 3. Write assembly language program to add to 8-bit numbers with carry. First numbers stored on memory location 2500h, second number on 2501H and store 8bit result on memory location 2502H and carry on 2503H.
6. Given the number 0XA0BOCODOE0F0, a. How many bytes for this number b. How many bits for this number c. Store in 8-bit computer with little endian system, and the starting address is 0x123, please show thedata memory map d. Store in 8-bit computer with big endian system, and the starting address is 0x123, please show the data memory map
............ signal must be low to access data on the odd addressed memory bank a. BHE and A0 b. BHE c. A0 d. M!IO