Calculate the factored load using LRFD load combinations 1. Dead Load: Superimposed DL: 20 PSF plus Self-Weight TBD 2. Roof Dead Load: Superimposed DL: 10 PSF plus Self-Weight TBD 3. Live Load: First Level: 250 PSF (Assume no live load reduction.) 4. Live Load: Second Level: 100 PSF (Assume no live load reduction.) 5. Roof Live Load: 20 PSF 6. Snow Load: 25 PSF (Assume no drifting of snow) 7. Rain Load: 6-inches of standing rainwater (assume that roof drainage plan and scupper size and spacing will allow up to 6-inches of standing water on the roof during a 1-hour, 100-year storm event.) 8. Wind Load: In lieu of determining wind loading from the ASCE/SEI 7-16 wind procedure, assume a uniform wind loading of 25 PSF on the windward face of the building and 5 PSF of uniform wind loading on the leeward face (a negative (or suction effect) loading). On the roof, assume that downward wind loading will not govern on the roof, but check the roof for an uplift loading of 15 PSF of wind loading. 9. Earthquake Load: Assume that wind loading will govern for this structure. 10. Ice Load: Assume that ice loading is negligible.

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm × 460 mm fully embedded in sand…

A:

Q: 4. A flat site is underlain by two layers over rock. The top layer is a CL with thickness = 3m,…

A:

Q: A Pipe 1 2 3 L(m) 120 180 60 D₁-8 cm -0.0288 20.0260 -0.0314 D₁-6 cm Three pipes are in parallel…

A:

Q: why elastic constants (E,K,G) are more predictable than fck (or) Sigma y (or) shear strength?

A: Elastic constants such as Young's modulus (E), bulk modulus (K), and shear modulus (G) are often…

Q: Based on a Greenshields' model, with a jam density of 120 vpmpl and a free flow speed of 60 mph,…

A: Given data in question Free mean speed (Vsf) =  60 mphJam density (Kj) = 120 vpmplDensity (K) = 60…

Q: The frame is subjected to a concentrated force of F = 1585 lb and a uniform distributed load of…

A: Note : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: are significantly by even a small curvature initial deflection, determine the column deflection…

A:

Q: under foundation is 150KN/m, check if the section satisfy this requirement or not? Assume free board…

A: Given:-bearing capacity of soil =150kN/m2earthquake coefficient=0.1gfree board=4mTo…

Q: Problem 1: A 6-m long cantilevered beam, 250 mm width x 600 mm deep, carries a uniformly distributed…

A:

Q: If P=30k, find the maximum absolute value of the shear stress Oxy in the beam. Beam: Y Cross…

A:

Q: One lane of a uniform section of highway has an optimum density of 70 vehicles per mile and an…

A: Optimum density = 70 veh/mileOptimum speed= 35 miles/hr Capacity of the lane (vehicle/hour) = ?

Q: The bear below is subjected to a moment of inertia for the beam's cross-section is 5×106 mm4. |-| If…

A: E = 210 GPaI = 5 * 106 mm4

Q: The solution of the consolidation equation is given by the series in the figure. By evaluation of…

A:

Q: P6-5. Sketch the bending stress distribution over each cross section. (a) M P6-5 (b)

A: Two members cross section are shown in the above figure. We have to draw bending stress distribution…

Q: RING 1 RING 2 $1 2 DJL $5 MAJOR STREET lead-lag lag-lag none $2 $6 BARRIER = Phase Number =…

A: Protected permitted operations are a combination of the permitted and protected modes. Left-turning…

Q: A Rectangular Hollow Section (RHS) member with span length of 4 m is subjected to an axial…

A: The objective of the question is to assess the suitability of a hot-rolled Rectangular Hollow…

Q: Determine coordinates of centroid of the shaded area shown in figure. All dimensions are in mm. 40…

A:

Q: Using the double integration method, determine the equation of elastic curve for the beam using…

A:

Q: A cylindrical tank of water is 2.0 m in diameter and 3.5 m tall. There is a 2.0 cm diameter hole at…

A: Diameter of the tank= 2.0 mHeight of the tank = 3.5 mDiameter of the hole: 2.0 cmHeight of the…

Q: What effective walkway width is needed if the hourly passenger demand of 8,750  is to be serviced at…

A:

Q: The 2.5 m x 3.5 m rectangular spread footing placed at a depth of 1.5 m supports a vertical load of…

A: To find:Factor of safety

Q: As might be expected, the load-carrying capacity and deformation under load of a column are…

A:

Q: The two beams are connected by an ideal pin at C. Draw the shear and moment diagrams for the…

A: Given:Required:Shear force and bending moment diagramMaximum magnitude of bending moment in each…

Q: Which cities are railroad gateways in the USA?

A: Railroad GatewayA railroad gateway refers to a city or location that serves as a major hub or…

Q: Determine the required development length in the beam and in the column for No. 10 bars shown in the…

A: Concrete strength(fc)=4300 psi,Yield strength of the concrete(fy)=60 ksi,Dead load(DL)=15 k,Live…

Q: For the slab shown in the figure, Fy= 420 Mpa, Col. Dimensions = 400 x 400 mm, check slab thickness…

A: Yielding stress of steel= fy = 420 MPaColumn dimension= 400 x 400 mm We have to check the slab…

Q: he beam in the figure below is subjected to a load P=2.5 kN at its end. Young's modulus is 210 GPa…

A:

Q: The hourly passenger volume is expected to be 8,750. The transit center is being design with 6, 2.5…

A:

Q: A triangular distributed load of max intensity w =370 N/m acts on beam AB. The beam is supported by…

A:

Q: Q2) a) Using Archeticture scale find the distance between the river and the building 40f

A: A scale ruler, often known as an architect's ruler, is used to measure actual distances on scaled…

Q: Use the singly constraint growth factor model to calculate the projected trips in Cell (1,2) for the…

A:

Q: If a dairy processing factory produces an average of 246 md of wastewater with a BODs of 1400 mg/lt.…

A: Given:Average wastewater production is 246m3/d with a BOD5 of 1400mg/lt.Per capita daily sewage flow…

Q: The isohyets for annual rainfall over a catchment were drawn and the area enclosed by the isohyets…

A: Isohyets are draw and the area enclosed by isohyets is given in the table below. Isohyets…

Q: Aluminum is a poor material to reinforce concrete with, especially as opposed to steel. There are…

A: The steel is used as reinforcement in the concrete to take the tension loads from the structure.…

Q: An orifice on a vertical wall has a head of 1.13 m of oil (sg=0.89). It discharges 6192 N of oil in…

A:

Q: Find the rotation of point B

A:

Q: A sieve analysis gives the following results: Sieve size (mm) Wt. retained (g) 1.000 0 0.500 64…

A:

Q: Carry out a moment distribution for the frame below (carry out ONE full interation). 6 kN/m 4EI 6m…

A:

Q: g) the maximum bending stress in timber. Enter your answer in MPa to 2 decimal places.

A:

Q: The half-life of 222 Rn is 4.2 days. A sample of 222 Rn is allowed to decay for 17.2 days and after…

A: As per question , This question is related to Environment Engineering.Given data - Half life = 4.2…

Q: In a given year, a catchment with an area of 1500 km² received 0.95 m of precipitation. The average…

A:

Q: The Warren truss loaded as shown in the fig at C and a hinge at G. By the method of s- members BC,…

A:

Q: Following results were recorded from a consolidation test on a specimen of saturated clay, each load…

A: After subjecting a saturated clay specimen to a consolidation test, each load was held constant for…

Q: For preparing PCC, would you prefer round and smooth aggregate or rough and angular aggregate?…

A: a. Choice of aggregate depends upon the type of construction. Round and smooth aggregates are used…

Q: 16: A member having the dimensions shown is to be used to resist an internal bending moment of M =…

A: A bending moment is the reaction created in a structural element when an external force or moment is…

Q: 6 kip.ft nax max A = kips C kip-ft 6 ft P 3 kips 4 kips. D ermine the maximum absolute values of the…

A: P= 5.5 kipsto determine the maximum absolute values of shear and bending moment-

Q: Problem #4: An 18-in.-long steel rod is subjected to a tensile (a) The tensile stress (b) The strain…

A:

Q: Which is the most efficient dust removal equipment for removal of sub-micronic dust particles from…

A: Which is the most efficient dust removal equipment for removal of sub-micronic dust particles from…

Q: Figure P 12.2. Estimate the ultimate point load or tip resistance Q, by each of the following 4…

A:

Q: 30. R.C.C. was developed and first used by:

A: Rcc was developed and first used by ?

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.