C.13 Indicate whether the following statements are correct or not then correct the incorrect statements 1) the multi pulse selected notching technique used in inverter is used to eliminate the low order harmonics and to reduce switching frequency, 2) In 3-phase half-controlled half-wave rectifier, the firing angle can be varied from 0 to 180 degrees while in 6-phase half-controlled half-wave rectifier can be varied from 0 to 150 degrees Q.14 Indicate whether the following statements are correct or not then correct the incorrect statements 1) In rectifier circuits, lower pulse number and connecting either primary or secondary of 3- phase winding in delta will reduce the harmonics content of the drawr. current 2) In thyristor triggering, the pulse width should be long enough to permit holding current to be established

C.13 Indicate whether the following statements are correct or not then correct the incorrect statements 1) the multi pulse selected notching technique used in inverter is used to eliminate the low order harmonics and to reduce switching frequency, 2) In 3-phase half-controlled half-wave rectifier, the firing angle can be varied from 0 to 180 degrees while in 6-phase half-controlled half-wave rectifier can be varied from 0 to 150 degrees Q.14 Indicate whether the following statements are correct or not then correct the incorrect statements 1) In rectifier circuits, lower pulse number and connecting either primary or secondary of 3- phase winding in delta will reduce the harmonics content of the drawr. current 2) In thyristor triggering, the pulse width should be long enough to permit holding current to be established

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

8-The waveform of output voltage of half-controlled three phase bridge rectifier in each cycle contains: Two- pulse six- pulse three- pulse 9-The DC supply voltage of single phase bridge inverter is 300V. For quasi-square wave output voltage with a 60 percent ON time, the RMS value of output voltage is: 232.37V 220.5V 270.9V 10-For three phase bridge inverter with 120° conduction and resistive star-connected load, the waveforms of: (a) The load current and line voltage are quasi-square. (b) The load current is quasi-square and line voltage is a six- step. (c) The load current is six- step and line voltage is quasi-square. 9.
Discuss the different types of protections available for a Silicon controlled rectifier (SCR). In what kind of situations is it required to connect a number of SCRs in parallel and series respectively?
4)Mark the correct statements: a) The frequency at the output of a half-wave rectifier circuit is 30 Hzb) The frequency at the output of a full-wave rectifier circuit is 60 Hz.c) To calculate the average voltage (DC) at the output of a full wave rectifier we use the formula: Ucc = 0.636 * Up.d) When using a bridged full wave rectifier, we know that the loss at the depletion barrier will be 2 * 0.7 Volts.e) None of the statements is correct.
Consider the half wave rectifier is supplied with 115V, 80HZ signal. Assume the number of turns in the primary to secondary ratio is 10:4. a. Calculate the average dc current through the load resistor 3.5K2. b. Calculate the value of input ac power, output dc power and frequency of pulsating dc output.
Calculate the theoretical output DC voltage of the center-tapped full-wave rectifier circuit and compare it with measured value. For the capacitive filter, obtain the theoretical values of the DC output voltage and the ripple voltage and compare these values with the measured quantities. Determine also the practical and theoretical values of the ripple factor.
Draw the form of bridge type full wave rectifier power source consisting of 4 layers (lowering, rectifier, filter, regulated) and briefly explain the role of each layer (by drawing the signal entering the layer and the signals coming out of the layer).
TOPIC: Thyristors and Phase Control Silicon-Controlled Rectifiers may be represented by the following transistor circuit. Explain this circuit's operation with and without a "triggering" voltage pulse at the gate terminal.
1. Calculate the theoretical output DC voltage of the half-wave rectifier circuit and compare it with measured value. For the capacitive filter, obtain the theoretical values of the DC output voltage and the ripple voltage and compare these values with the measured quantities. Determine also the practical and theoretical values of the ripple factor. 2. Calculate the theoretical output DC voltage of the center-tapped full-wave rectifier circuit and compare it with measured value. For the capacitive filter, obtain the theoretical values of the DC output voltage and the ripple voltage and compare these values with the measured quantities. Determine also the practical and theoretical values of the ripple factor. 3. Repeat the calculations for the full-wave bridge rectifier and filter circuit. 4. Determine the peak inverse voltage (PIV) on each diode in the three rectifier circuits. 5. If diode D4 in the bridge rectifier circuit of Figure 5 was removed or burned, explain the operation of…
Explain the theory of the Generation High Voltage Direct Current(HVDC) using Rectifier Circuits..And also explain the half wave rectifier of the HVDC.. *High Voltage Engineering *Need two page long the teory
Calculations and Discussion 1. Calculate the theoretical output DC voltage of the half-wave rectifier circuit when C=47UF and compare it with measured value. 2. Calculate the theoretical output DC voltage of the full-wave bridge rectifier circuit when C=100uF and compare it with measured value. 3. What value of filter capacitor is required to produce 1% ripple factor for a full-wave rectifier having a load resistance of 1.5kQ? Assume that the peak value of the output voltage is 18V.
4) Choppers is a a. AC - DC converters b. AC - AC converters c. DC - AC converters d. DC - DC converters 5) A single phase dc ac converter is also known as a. Rectifier b. Inverter c. Chopper d. Regulator
In a three-phase half-wave diode uncontrolled rectifier using 6 diodes, __. a) all diodes conduct together b) only two diodes conduct at the same time. c) only one diode conducts at a time. d) none of the above mentioned.