Question 5 Determine the impedance Z, for the maximum average power transfer and the value of the maximum average power absorbed by the load in the network shown in Fig. 2Vx 202 5 www +1 12/0°V -j1 ΩΡ 192 Z

Question 5 Determine the impedance Z, for the maximum average power transfer and the value of the maximum average power absorbed by the load in the network shown in Fig. 2Vx 202 5 www +1 12/0°V -j1 ΩΡ 192 Z

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Related questions

Q: Ri= 42 حمد 123=101 VL R2 =21 um ++ t EV P4= In &V Rs = Sn

A: it is asked to find the currents through each load resistors

Q: In the following circuit: a) What is the Vrs in this circuit? b) Find the Thevenin Equivalent…

Q: In the circuit below, how many super nodes there are: 3 ΚΩ 4 ΚΩ 2 ΚΩ 10v (+ 4 ΚΩ 3 ΚΩ 0.5V + 6 ΚΩ +…

A: Given one circuit with nodes. Need to find number of super nodes in a given circuit.

Q: 20v Tunes #2 Encontrar la pitencia en la carga R 1 t 1K 2K LK 3K 3K< 1K 4K 3 5K R₁ TIT

Q: Q1. Analyze the circuit of Figure 1 by using Nodal analysis to calculate the voltage at each node…

A: Given Data:A DC circuit with,Voltage source Resistors,To Find:Nodal Voltages

Q: We wish to design the circuit shown in figure for a voltage gain of 0,7 with a power budget of 5 mW.…

A: Solution-

Q: •EC. 1.5 THEVENIN'S THEOREM 1. In the circuit of Figure 1.19, what is Thevenin's tension? What about…

A: In this questionWe need to determine the Thevenin voltage Vth and Thevenin resistance Rth with…

Q: The sizes of the given circuit elements are given below. What is the average power delivered by the…

A: In a single-phase transformer dot convention of the winding is of importance. In the given circuit…

Q: Find the current across the resistor 2 22 in Ampere while the switch S is closed for a long time. A)…

Q: (100 V DC serial motor has a starting current value of 50 A. Total armature resistance (Ra) value is…

Q: Q5) For the following MOSFET circuit, VT=2V, K=0.25, VDD=10V 280ΚΩΣ 160k 10ΚΩ a) Is this a P-Channel…

A: The MOSFET circuit Given K=0.25 , VT=2V We need to calculate a) P or N channel MOSFET.b) operating…

Q: KLO 20 -j40 120, jin 20 -J20 j20 3.0 Soru -2) Devrede K-30 ise "lo" akımını hesaplayınız.…

Q: A three-phase 765 kV, 60Hz, 300 km, line has the following positive sequence impedance and…

A: Given values are =The value of impedance and admittance for the length of 400 km is =

Q: calculate the curents

Q: Design a buck converter to convert 109 V dc supply voltage to 45 V output voltage across a 15 ohm…

A: given thatto design the buck converter according to given values are input voltage VS = 109 Voutput…

Q: A six pole synchronous generator operates at 60 Hz. Find the speed of operation

A: It is given that:

Q: О BP O HP 0 BS U R 190C R L

A: For this circuit we need to calculate the type of filter.Circuit:-

Q: 1. From the given block diagram below, find the following: a) the differential equation of the…

A: A signal flow graph (SFG) is a graphical representation of a system or network using nodes and…

Q: The PID controller affect on the system : a) Eliminate steady state error and increase over shoot b)…

A: The above question is based on PID controllers in control systems.It is a cascade combination of…

Q: Find Thevenin equivalent circuit for the terminals across 2Ω resistor. ΤΩ Φ Find Norton equivalent…

Q: R₂ R₁ L с 19.

Q: A load consumes 44 kW at 0.82 pf lagging from a 22020° V rms, 60-Hz line. A capacitors of 900 μF is…

A: I have written this solution as handwritten solution. Hope you find the perfect solution.

Q: Vs= 40 V Z1 = 1 0hm Z2 = j2 Ohm Z3 = 2 Ohm Z4 = -j4 Ohm Z5 = 1 Ohm Z6 =j2 Ohm Z7 = 2 Ohm Z8 = -j4…

Q: In an RL high-pass filter, the output is taken across the inductor and the output leads the input.…

Q: 19.15 For the two-port circuit in Fig. 19.76, 40 60 80 120 [z] (a) Find Z₁ for maximum power…

A: Given Data:A two-port network with,Impedance matrix Source voltage Source resistor To Find:The load…

Q: After the switch S is kept open for a long time, it is closed at t=0. What is the current across the…

A: We need to find the current across the resistor 3ohm at t=0 in amp

Q: ►Y(s) transfer function is given by its Nyquist diagram. Calculate the Bode parameters (amplitude…

Q: 2. Express the following functions as a cosine: a. 10 sin(wt +30°) b. -40 sin(wt - 70°) c. 25 sin(wt…

Q: Consider the following circuit R Us M +v₁ (t)- yilt) + L c. The inductive impedance is Z = L Vo(t)…

A: Since multiple subparts have been asked, as per Bartleby guidelines only the first 3 have been…

Q: The voltage impulse response of a circuit is shown below in figure (a). The input signal to the…

A: The impulse response of the circuit isThe input to the circuit isWe need to determine the output…

Q: Describe whether the following statements are (True) or (False) CX704 4- When the zero adding to the…

A: We need to check whether the following statements are TRUE or FALSE.1. When the zero adding to the…

Q: 2V (#) 2F 11 fullt 3-2 NC₂O 4^ Ⓒ 2A Calculate capacitor voltage for tho for the circuit below. given

Q: the rotor frequency of a four-pole, 60 Hz induction motor with 5% full * load slip is 50 H7

A: Number of poles is given P = 4.Frequency is given f = 60 Hz.Slip is given as

Q: a) The voltage VF applied to the field circuit b) The internal voltage EA c) The machine speed in…

A: The above question is based on a separately excited DC motor.Since multiple subparts to the same…

Q: Calculate the output impedance for the circuit shown in figure. Assume VA = ∞0. Şekildeki devre için…

A: given thatresistances are

Q: > A series-connected circuit has R=2 2 and L=1 mH, C=400 nF, vS(t) = 20sinwt V. Determine amplitude…

A: Given data are:L=1mHC=400nFVs(t)= 20sint VThus maximum Voltage Vm=20V.

Q: Solve the following differential equation using Laplace's transformation d'y dy dx + +y=8(t-2), 8:…

Q: Write 5 difference between induction motor and synchronous motor?

Q: ► Choose the proper algebraic form of the given time dependent signal. i(t) A 10 0 -10 2 4 O 10…

A: The time dependent signal isWe need to determine the proper algebraic form of the given time…

Q: 8002 80V t=0 3F 0.5i(t) 300 www 5002 vi(t) The switch in the circuit has been closed for a long…

Q: 2.02 XZ0° A ww 292 -j20 Z YZ0° V Soru 1) Devrede X=24 ve Y-39 ise maksimum ortalama güç transferi…

A: The given problem can be solved by using Thevenin theorem and maximum power transfer theorem. The…

Q: Design a buck converter to convert 109 V dc supply voltage to 45 V output voltage across a 15 ohm…

A: Design a buck converter,DC supply voltage,Output voltage, Load resistor

Q: 202 XZ0° A ΖΩ -j20 Z YZ0° V estion 1) If X=20 and Y=36 in the circuit, calculate the "Z" impedance…

Q: L[cosw(ta)u(ta)]= as s² + w²

Q: We wish to design the circuit shown below for a drain current of 4 mA. Compute R₂ such that the…

Q: Problem 2.12: A three phase transmission line having conductor radius 1.25 cm and spaced 3 m apart…

A: it is asked to find the inductance of each conductor in given three phase transmission system

Q: Using the 74LS00 NAND gate chip, construct the circuit in the schematic and complete the…

A: The logic diagrams are1)2)We need to fill the truth table given along with the the functioning of…

Q: In the circuit shown below, what is the minimum allowable value of VoD if M₁ must not enter the…

A: given that the values are…

Q: 1- Application of Norton's theorem to a circuit yield a- Equivalent current impedance in series c-…

Q: The operational amplifier circuit shown in the figure is a two-stage amplifier circuit. 1. Find the…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Maximum power transfer theorem:

VIEW

Step 2: Finding thevenin impedance:

VIEW

Step 3: Determining load impedance for maximum power:

VIEW

Step 4: Determining thevenin voltage:

VIEW

Step 5: Determining maximum power:

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

NEED ASAP please solve this problem,Maximum Average Power Transfer. Please show full and complete solution Note: Answer from the book for Pmax is lower than 50W
a) Find the average power dissipated in the line shown.b) Find the capacitive reactance that when connected in parallelwith the load will make the load look purely resistive.c) What is the equivalent impedance of the load in (b)?d) Find the average power dissipated in the line when the capacitivereactance is connected across the load.
The variation of the load is considered over a period of month in the monthly load curve. Select one: True False
IL 220230° Load P = 2 kW pf = 0.9 lag Assuming that the source is operating at 60 Hz, determine the following: a.) The value of the current I, in phasor form the magnitude, degrees for the angle) b.) What is the reactive power Q of the load in (volts for KVAR? c.) Is the load consuming or supplying Q? d.) What is the apparent power S of the load in KVA? e.) What is the load resistance? Express your answer in Ohms. f.) What is the load inductance? Express your answer in millihenries.
3 Two impedances z1 and z2 when connected separately across a 230V 50HZ supply consumed 100w and 60W at power factor of 0.5 lagging and 0.6 leading respectively. If these impedances are now connected in series across the same supply, find a) total power absorbed and overall p.f. b) the value of the impedances to be added in series so as to raise the overall p.f. to unity, c) draw the circuit and diagram/s.
A source is connected to two loads impedance Z, and Zz in parallel. Choose the correct statement(s): Select one: a. The total average power delivered by the source is the sum of the apparent powers dissipated by Z, and Z2 O b. The total apparent power delivered by the source is the sum of the apparent powers dissipated by Z1 and Z O c. None of these O d. The total average power delivered by the source is the sum of the real powers dissipated by Z, and Z2
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
For the following network find a) Isb) PT, QT, ST and PFTc) Draw power triangle d) Raise the power factor to unitye) Compute Is after raising the power factor
A single-phase load consumes 10 kW at 0.9 power factor lagging from a distributed generation (DG) unit that is rated at 220 V. What are the magnitude and phase angle of the current drawn from the DG? If another single phase load rated at 10 kW and 0.8 leading power factor is connected in parallel to the same DG, what is the magnitude of the current drawn by the load? What is the current drawn from the DG supplying both loads? Give your answers in a polar form.
The two loads in the circuit shown can be described as follows: Load 1 absorbs 8 kW at a leading power factor of 0.8. Load 2 absorbs 20kVA at a lagging power factor of 0.6. 1. Determine the power factor of the two loads in parallel.2. Determine the apparent power required to supply the loads, themagnitude of the current, Is, and the average power loss in thetransmission line.3. Given that the frequency of the source is 60 Hz, compute the value ofthe capacitor that would correct the power factor to 1 if placed inparallel with the two loads. Recalculate the values in (b) for the loadwith the corrected power factor.
An 11kV, three phase transmission line has a resistance of 2 ohm and reactance of 4 ohm per phase. The efficiency of the line when supplying a load of 4MW at 0.8 lagging power factor is nearly .. Select one: O a. 97.8 % O b. 90.6 % OC.95.4 % O d.99.2 %
Problem 4 An electric saw, a wood shaper, and a motor load of a workshop establish a 18 kVA power demand at 0.5 power factor lagging on a 208 V, 60 Hz supply. d) Determine the power-factor capacitor that must be placed in parallel with the load to raise the power factor to unity.