Question b 4 mL450 mmA,150 mm[50 mm|g350 mm50 mmFigure laFigure 1b Before a diver jumps into the water, he/she stands at point C, causing a deflection ofthe board A-B-C in the figure. The board A-B-C has a modulus of elasticity of E = 15MPa with the sketched dimensions and cross-section (fig. 1b). Assume g=10 m/s?.Provide all steps of your working and solutions handwritten; include diagrams andcoordinate systems.Determine the reactions at each support A and B. Use the variable w for theweight of the diver; include a free-body diagram.b.Determine the shear-force and bending-moment diagrams of the whole board.Label all important points in your diagrams; include a free-body diagram. Analyseyour bending-moment diagram and shear force diagram and explain the consistencybetween your diagrams.

Answered: Image /qna-images/answer/1099ccaf-0782-44b9-b2a0-6a778662deaf.jpg

Before a diver jumps into the water, he/she stands at point C, causing a deflection of the board A-B-C in the figure. The board A-B-C has a modulus of elasticity of E = 15 MPa with the sketched dimensions and cross-section (fig. 1b). Assume g=10 m/s². Provide all steps of your working and solutions handwritten; include diagrams and coordinate systems.

Before a diver jumps into the water, he/she stands at point C, causing a deflection of the board A-B-C in the figure. The board A-B-C has a modulus of elasticity of E = 15 MPa with the sketched dimensions and cross-section (fig. 1b). Assume g=10 m/s². Provide all steps of your working and solutions handwritten; include diagrams and coordinate systems.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 20 mm² and is made from 6061-T6 aluminum. (Figure 1) Figure 1.5 m • 300 N/m -2 m 1 of 1 > Part A Determine the vertical deflection of the bar at D when the distributed load is applied. Express your answer to three significant figures and include the appropriate units. dp = Submit μÃ Value Provide Feedback Request Answer Units
A rigid bar is supported by a spring as shown in figure below: 50 kN/m B 5m - 5m The deflection of point C will be 10 kN VC
5. A steel bar 50mmx50mm in cross-section is 1.2 m long. It is subjected to an axial pull of 200 KN. What are the changes in length, width and volume of the bar, if the value of Poisson s ratio is 0.3 ? Take E as 200 GPa. Answer :Al-0.48mm, Ab-0.006mm and AV-480 mm'.
A 5 m long steel rod is fixed vertically and loaded with a mass of 500kg which causes the rod to stretch by 5 mm. It has cross-sectionalarea of 50 mm2. Find the modulus of elasticity of the steel rod.A. 98.06 GPa C. 118.06 GPaB. 138.06 GPa D. 158.06 GPa
The uniform 200-1b beam is initially at rest when the forces are applied to the cables. Set F₁ = 140 lb and FB = 240 lb. (Figure 1) Figure A 12 ft FB B 60° 1 of 1 Part A Determine the magnitude of the acceleration of the mass center at this instant. Express your answer to three significant figures and include the appropriate units. ag = Submit Part B α = Submit μА Value Request Answer Determine the angular acceleration of the beam at this instant. Express your answer to three significant figures and include the appropriate units. ЦА Value Units Request Answer ? Units ?
Calculate the value of the deflection at point B due to concentrated load P in the form ??=??????????? Note: EI will cancel out in further calculations. Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
PROBLEM 2 As shown in the figure, neglecting the weight of the rods and for the loading shown, determine the deflection of point C and of point B A STEEL 3.0 m E=200 GPa d= 38 mm 3.5 m P-60 kN BRASS E=105 GPa 2.0 m d= 25 mm D VQ = 150 kN
Replace the loading on the frame by a single resultant force. Suppose that F₁ = 450 N F₂ = 650 N, F3 = 950 N, and F₁ = 600 N. (Figure 1) igure F₁ 0.5 m F₂A -1 m- 1.5 m 1m B T0.5 m x 1 of 1 ▼ Express your answer to three significant figures and include the appropriate units. FR = Submit Part B 0 = Submit Part C O x = μA Value Determine the angle between the resultant force and the x axis. Express your answer using three significant figures. VE ΑΣΦ || Ivec Request Answer Request Answer Units μA Value ? Specify where the line of action of the resultant force intersects a horizontal line along member CB, measured from end C. Express your answer to three significant figures and include the appropriate units. Enter positive value if the line of action intersects a horizontal line CB to the right from end C and negative value if the line of action intersects a horizontal line CB to the left from end C. Units ? ? °, measured clockwise from the positive x axis
The fixture shown in Figure 5 is fixed at point A and free at point C. The frame is made from a steel bar 50 mm wide and 75 mm thick. Assuming Young's modulus for steel to be 200 GPa, determine the vertical deflection at C due to the applied load of 5 kN. Use Castigliano's theorem and ignore any axial or shear deformations. A 4.5 m Figure 5 kN с T B 5 (not to sca 1.5 m Cross section ↓ 0 ↑ h b = 50 mm = 75 mm
H.W.1 A steel pipe that contains castor oil (p=1.8624 slug/ft) is 6 ft in diameter. Determine the forces exerted on the portion labeled A-B in Figure below if the pipe is filled halfway. Determine also the location of the forces. Pipe length (into the paper) from joint to joint is 8 ft. 6 ft Fy Ih Fx A A A
Two wires support a weight W. The stresses in the wires AB and AC are not to exceed 81 MPa and 161 MPa, respectively. The cross- sectional area of the two wires are 353 mm? for AB and 139 mm2 for AC. Wire AB is inclined 23-degrees with the horizontal and wire AC is inclined 46-degrees with the horizontal. Give the largest weight W (kN) that can be supported by the wires? Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. B A W
Q3: Figure (3) shows a punching machine of plate (thickness 2 mm).Punching operation is applying many times to make thousands holes (d-4 mm) through cam (2) which attaches with the ram (1) from two sides and moves it up and lowering down by action of weight (1000N). Assume the ram (1) is circular cross section. Requirement: Select the correct answer of following: 1. The ram (1) subjected to static bending stress at section (X-X): 1800ND Flgure (3) X- B. 100 mm A: True B: False 2. The ram (1) subjected to reversed load at section (Y-Y): B. False 3. The diameter of ram (1) at section (X-X) is (44603 mm): B: False 1- A: True A: True 4. The diameter of ram (1) al section (Y-Y) is (9.694 mm): B: False A: True For ram (1) and pin (b): S,-160 MPa S,-210MPA S-100MPA 5. The torque required to rotate cam (2) is (10000 N.mm): A: True B: False 6. The plate material can be punched by this mechanism has (S,-39.788 MPa): N= 2.5 A: True 7. The diameter of pin (b) on the ram (1) is (6.307 mm): B: False…