H.W.1 A steel pipe that contains castor oil (p=1.8624 slug/ft³) is 6 ft in diameter. Determine the forces exerted on the portion labeled A-B in Figure below if the pipe is filled halfway. Determine also the location of the forces. Pipe length (into the paper) from joint to joint is 8 ft. | サ 6 ft B Fy Fx B.

H.W.1 A steel pipe that contains castor oil (p=1.8624 slug/ft³) is 6 ft in diameter. Determine the forces exerted on the portion labeled A-B in Figure below if the pipe is filled halfway. Determine also the location of the forces. Pipe length (into the paper) from joint to joint is 8 ft. | サ 6 ft B Fy Fx B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A. Determine the magnitude and direction of the hydrostatic force acting on the gate using the PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism as part of your solution. Express your answer in kips. B. Determine the magnitude and direction of the force exerted on the plate by the ridge. Illustrate and label the FBD of the force system. Express your answer in kips. Show complete solution (Round off ONLY the final result to three decimal places. Indicate the unit of your final answer)
A line is recorded as 472.90 m long. It is measured with 0.65 kg tape which is 30.005 m long at 20 degrees Celsius under a 50 N pull supported at both During measurement, the temperature is 5 degrees Celsius and the tape is suspended under a 75 N pull. The line is measured on 3% grade, E = 200 GPa, cross-sectional area of tape is 3 mm2 and the coefficient of linear expansion is 0.0000116 m per degree Celsius. Compute the actual length of tape during measurement Compute the total error to be corrected for the inclined distance What is the true horizontal distance?
Question 2 A rectangular plane surface is 3 m wide and 6 m deep. It lies in vertical plane in water. Calculate and determine the total resultant force (kN) the position of the center of pressure (COP) on the plane surface when its upper edge is horizontal and 3.5 m below the free water surface. Represent your result on a sketch. [lc xsin? e BH Hint: show all the steps. hp = hc + Ic 12 g= 9.81KN/m hcxA
! Required information A brass pipe having the cross section shown has an axial load P applied 5 mm from its geometric axis. The horizontal deflection at the midpoint Cis 4.7 mm for the applied load. Use E= 120 GPa. 120 mm 2.8 m t = 6 mm B Determine the load P. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The applied load is kN.
The box wrench is subjected to the 50 lb force. (Figure 1) Figure 2 in. a 12 in. 0.5 in. A B Section a-a 1 of 1 50 lb Part A If t, determine the principal stress at point B on the cross section of the wrench at section a-a. Express your answers using three significant figures separated by a comma. VG ΑΣΦ [41 01.02 Submit Part B * Incorrect; Try Again; 29 attempts remaining Previous Answers Request Answer Tmax in-plane = vec Determine the maximum in-plane shear stress at point B on the cross section of the wrench at section a-a. Express your answer to three significant figures and include the appropriate units. μA Provide Feedback Value Submit Previous Answers Request Answer [w] ? Units * Incorrect; Try Again; 28 attempts remaining ? ksi
Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate ftop at the ends. (MPa), consider sign convention (- for compression, + for tension) Skw/m EXCLUD in6 SELFWEI6HT 300 =P P=300 kN ISM オ 400 片 de = 24 IN m3 N.A. 800 70
Determine the load that the steel tube could carry if the change in temperature is 25 °C. |P= 50 KN II Bronze Steel Tube E = 200 GPa a = 11.70x10*/c E = 83 GPa a = 19x10*fc 90 mm| 100 mm
The degree of indeterminacy for the structure is given as 24 kN 5 m w = 12 kN/m A B 10 m 3A m a. Three O b. Zero C. Five d. Four
I RevieW The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Part A Determine the state of stress at point B. Express your answers, separated by commas, to three significant figures. IVα ΑΣφ. vec ? OB =, (Tzy)B =, (T2)B = ksi (C), ksi, ksi Figure 1 of 1 > Submit Request Answer < Return to Assignment Provide Feedback 9 in. 200 lb 300 lb 1200 lb in.
Qs.The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft. Calculate the maximum diameter of the cylindrical tank if the internal pressure is 110 psi. Also discuss the joint strength and diameter of tank requirement for the given conditions .If you dont know the answer please skip and let others do , dont post wrong answer, dont waste qsn
Please make sure to draw all diagrams. All units must be included. Problem 3: Note: Make sure to draw all diagrams. All Units must be included. 1. Determine the stretch in each of the two springs required to hold the 20kg crate in the equilibrium position shown. Each spring has an un- stretched length of 2m and a stiffness of k=300N/m. Ans. SA 0.218m, Sg 0.327m 12 m 1. Draw Free-Body Diagram(s) 2. Write Equations of Equilibrium 4 m 6 m 3. Solve for all unknown forces 4. Find the Stretch in each of the two springs
a. Determine the magnitude and direction of the hydrostatic force acting on the gate using PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism as part of your solution. Express your answer in kips. b. Determine the magnitude and direction of the force exerted on the plate by the ridge. Illustrate and label the FBD of the force system. Express your answer in kips.