b) The following data refers to an axial flow turbines. Stream speed at the exitVf,Vf₂blade150 m/s, the ratio -=0.75;2=0.78, Mor W, = 2.8kg/s, dischargeu=ublade angle for both stator and rotor = 20° calculate:a) The inlet rotor blade angleb) The power developmentc) The degree of reactiond) Power lost in friction

Answered: Image /qna-images/answer/eb96bce1-4996-46d3-b754-397445816b6c.jpg

b) The following data refers to an axial flow turbines. Stream speed at the exit blade = 150 m/s, the ratio V₁ = 0.75;- = 0.78, M or W₁ = 2.8kg/s, discharge Vf₂ u u blade angle for both stator and rotor = 20° calculate: a) The inlet rotor blade angle b) The power development c) The degree of reaction d) Power lost in friction

b) The following data refers to an axial flow turbines. Stream speed at the exit blade = 150 m/s, the ratio V₁ = 0.75;- = 0.78, M or W₁ = 2.8kg/s, discharge Vf₂ u u blade angle for both stator and rotor = 20° calculate: a) The inlet rotor blade angle b) The power development c) The degree of reaction d) Power lost in friction

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m/sec. 3. Specific speed. B) What importance has the ratio? M = (mean diameter of Pelton wheel)/ (least diameter of jet) in designing the Pelton turbine.
Q2) Pelton wheel A) Power produced by a Pelton wheel is (596.8*10°Watt) under a head of (150 m) with wheel rotating speed equal to (360 r.p.m), the efficiency overall is (85%) and assumption of velocity coefficient is (0.985), velocity ratio is (0.46). Find 1- Diameter of the wheel 2- Diameter of the jet 3- Discharge
Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m'/sec. 3. Specific speed.
Q.2. A catrifugal pump is operating at the rotation rate of 750 rpm. Water leaves the blade at 40° from the radial direction. Water enters to blade at 80° from tangential direction( off design condition). The inner and outher respectivelly. The width of the impeller is 14 cm. Flow rate of the pump is 0.60 m³/s. a) Draw the velocity triangles at inlet and outlet of the blade. Determine; b) the blade angles, Bi and B2. c)Net head and power of the pump, d) Specific speed of the pump, choose the type of the pump ( radial-mixing and axial flow types) radius of the impeller is 12 cm and 18 cm 1
Q-) When a centrifugal pump tried at a constant rotation speed of n = 1470 rpm, the following values were found: Q: dm3/s 0 10 20 30 40 50 55 60 70 H: m 460 495 507 500 490 460 449 430 390 Hy= 120 + 0.136Q2(Q→dm3s⁄;H→m) A-) Indicate the operating point of the pump. B-)What would be the operating point if two of this pump are connected in parallel to the same discharge pipe?
A two-jet Pelton wheel is required to produce 2MW power with 400rpm. The diameter of the wheel is 1.5m. Gross head measure from the water surface in reservoir to the nozzle is 200m. Head loss in the penstock and nozzle is 10% and the deflected velocity by the bucket reduced 10%. If the deflected angle is 1650, determine; a) Nozzle head b) Euler Head c) Velocity ratio d) Diameter of jet
Q2) Design a Francis turbine with the following specifications: Head available 68m Speed Power output Hydraulic efficiency Overall efficiency Flow ratio X 750 rpm 330kw 94% 85% 0. 15 0.1 Breadth to diameter ratio at inlet Outer to inner diameter ratio 1/2 Assume 6% of circumferential area of runner occupied by thickness of vanes and flow velocity remains constant and flow is radial at exit.
The diameter of the discharge pipe of pump is 15 cm and that of intake pipe is 20 cm. The pressure gage at discharge reads 257 kPa and a vacuum gage at intake reads 195mm Hg. The flow rate is 90000 L/min and the applied torque in the pump shaft is 6.5 kN.m for a mechanical efficiency is 88% determine a.) the pump used; b.) the pumps to be used for a four-parallel pump arrangement.
1- A double jet of Pelton turbine driven by double nozzles to produce (4250 kw) to the shaft of an electrical generator when running at (400 rpm). The height of (180 m). wheel diameter is (1450 mm). The velocity of relative= 0.9 of jet velocity. If the angle of bucket is (165'), determine: a) Hydraulic efficiency b) Diameter of the jet
Example (6-1): At the best efficiency point a centrifugal pump, with impeller diameter D=8 in, produces H= 21.9 ft at Q=300 gpm with N=1170 rpm. Compute the corresponding specific speed using a) U.S. customary units. B) SI units (rad/sec, m/sec, m'/sec").c) European units (rev/sec, m/sec, m/sec?). Develop conversion factors to relate the specific speeds.
Using the specific rotation speed, what would be the best turbine option for a waterfallof 120m and a flow of 6m³/s, working with a 12-pole generator? And what would be the nqa for thissituation?ALTERNATIVESa) Francis Turbine Normal, nqa= 121.88.b) Kaplan turbine, nqa= 7312.89.c) Slow Francis Turbine, nqa=98.15.d) Deriaz Turbine, nqa= 290.5.e) Pelton turbine, nqa= 29.05.
In Maria Cristina Hydroelectric Project, the available head is 150m, the head loss is 4.4% of the available head, the water flow is 1.3 cubic meter per second, the turbine efficiency is 86% and the generator efficiency is 94%. Determine: a.) The water power in kW b.) The Generator power in kW c.) The estimated annual energy generated by the plant in kW-hr per year d.) The estimated annual income of the plant if the cost of generated energy is P0.65 /kW-hr