Assume an analog temperature sensor shown in Figure 1 has output voltage of 0V to 5V. This sensor output the voltages when measuring temperature that range from 0℃ to 100 °C. Design an 8085-microprocessor system that interface with the sensor using analog to digital converter AD0804 as shown in Figure 2 through the following compulsory steps:

Assume an analog temperature sensor shown in Figure 1 has output voltage of 0V to 5V. This sensor output the voltages when measuring temperature that range from 0℃ to 100 °C. Design an 8085-microprocessor system that interface with the sensor using analog to digital converter AD0804 as shown in Figure 2 through the following compulsory steps:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Comparing the performance with controlled rectifier circuit which one of the following statement is correct for DC -DC chopper ? O a. Regenerative braking process is very slow O b. Efficiency is poor in chopper circuit O c. small filters are required O d. Switching frequency is not responsible for output ripples
A 555 timer configured to run as an astable mode oscillator is shown in Figure 1. If the output is needed to have 30% duty cycle, i) Determine the required value of Rị if R2 = 7kN. ii) Determine the frequency of the output. iii) Draw the charging and discharging phase of capacitor Cext and its relation with the output waveform. ASsume Vcc = 12 V. +Vcc (4) |(8) R1 RESET Vcc (7) DISCH 555 D1 R2 (6) THRESH (3) OUT (2) TRIG (5) CONT GND :Cext 0.01 µF (1) 0.01µF Figure 1
Answer the following. Use a detailed explanation. 1. In reverse bias condition, what happens to the current if the temperature increases 10 degrees Celsius. 2. What semiconductor is frequently used for its high reliability at high speed? 3. What type of rectifier circuit has the highest dc output?
b) The waveforms shown in figure (1) are the trigger and the output waveforms of a monostable multivibrator using 555 timer. From these waveforms and for each output cycle answer the following: 1) The value of the charging time interval of the capacitor is seconds. 2) The value of the discharging time interval of the capacitor is seconds. 3) The value of the time interval that the transistor remains ON is seconds. 4) The value of the time interval that the transistor remains OFF is seconds. 5) The S input of the S-R flip flop logic (1) when %3D Sutrigger/v 7v 26m 12v - 4m Figure (1)
Let the values are R1=622.8ohm,R2=915.95 ohm ,The error voltage is =7.9 Volt.and the initial value of output is 5.5 Volt. Vout =
A single phase fully controlled bridge rectifier circuit has DC output voltage 170 V for an AC supply voltage of 200 V rms. Find the firing angle delay of the circuit for the following cases (a) Converter mode (b) Inverter mode Converter mode delay angle Inverter mode delay angle
(i) A single phase half wave controlled rectifier is operated from a 140 V, 50 Hz supply and the load resistance is 5 Q. If the average output voltage is 12.5 % of the maximum possible average output voltage calculate (a) firing Angle (b) average output current (c) draw the output voltage waveform (ii) With neat sketch explain the dynamic turn ON characteristics of the device which is used in high power applications. firing Angle average output current
Comparing the performance with controlled rectifier circuit which one of the following statement is wrong for DC -DC chopper ? a. small filters are required O b. Regenerative braking process is very slow O c. Switching frequency is responsible for output ripples O d. Efficiency is better in chopper circuit
By comparing the performance of DC -DC chopper with controlled rectifier circuit which one of the following statement is wrong ? O a. Efficiency is better in chopper circuit b. small filters are required in chopper circuit O c. Regenerative braking process is very slow in chopper circuit O d. Switching frequency is responsible for output ripples in chopper circuit Clear my choice
AC VMAX VRMS Ov DC VoCEO Rectified Output Waveform V MAX =D 0.318V MAX =0.45V RMS d.c. calculate the (a) average dc output voltage and (b) RMS output voltage using the equation for converting the peak output of a half-wave rectifier to direct current.
In a Full-Wave Controlled Rectifier (Full-Wave Bridge Rectifier) with a resistive load and a sinusoidal AC input, the thyristors in the control circuit are triggered with a delay angle a (0
Draw schematics for the following circuits/components: a) And Gate b) Rectifier circuit c) NPN BJT Amplifier with current directions d) OR Gate c) Diode