Signal and system A sampling operation will be carried out.We want to sample z(t) = 6, 6e-0,8t cos(272t) continuous signal. Sampling will start at time 0. If the sampling frequency is Fs=10, which one of the following isnot one of the sample values?Hint: Find the time interval between two consecutive samples, T.Find z(07,), z(1T.), z(2T)...Only your choice here will be taken into account. Do not provide a handwritten solution.O a. -4,55O b. 1,26O c. 3,73O d. -3,05Oe. -4,20.O f. 4,42O g. 1,48O h. 1,88

Sampling frequency Asked to find which of the given samples is not a valid sample.

A sampling operation will be carried out. We want to sample z(t)= 6, 6e-0,8t cos(22t) continuous signal. Sampling will start at time 0. If the sampling frequency is Fs=10, which one of the following i not one of the sample values? Hint: Find the time interval between two consecutive samples, T. Find z(07,), 2(1T,), z(2T,)... Only your choice here will be taken into account. Do not provide a handwritten solution. O a. -4,55 O b. 1,26 O c. 3,73 O d. -3,05 O e. -4,20 O f. 4,42 O g. 1,48 O h. 1,88

A sampling operation will be carried out. We want to sample z(t)= 6, 6e-0,8t cos(22t) continuous signal. Sampling will start at time 0. If the sampling frequency is Fs=10, which one of the following i not one of the sample values? Hint: Find the time interval between two consecutive samples, T. Find z(07,), 2(1T,), z(2T,)... Only your choice here will be taken into account. Do not provide a handwritten solution. O a. -4,55 O b. 1,26 O c. 3,73 O d. -3,05 O e. -4,20 O f. 4,42 O g. 1,48 O h. 1,88

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the minimum sampling frequency that must be used to sample the signal x(t) = 3cos(50 * pi * t) + 10sin(300 * pi * t) - cos(100 * pi * t) to avoid aliasing?a. 50 Hzb. 100 Hzc. 200 Hzd. 300 Hz
1) what is the fundamental frequency (in units of Hz) of the given signal is 2)The period of the given signal is 3)The harmonic frequencies (in unit Hz) of this signals are
ス45 Rb M[Q4] The signal r(t) = 2 sin(200rt) is sampled at a rate of 800 samples per second. Draw 1.5 cycles of the analog signal and show where sampling occurs on the waveform. M[Q5] The signal r(t) = 100 sin(200rt) +75 cos(300rt) is sampled every 20 ms. (a) Is the sampling adequate? If not, what would be the adequate sampling rate? (b) plot the spectrum of the sampled signal, %3D
ASAP
A typical digital signal processing (DSP) system is given in figure below. ADC has 100MHZ sampling clock and every samples will be captured by FPGA for backend processing. An interpolator increases the sampling rate by a factor of 4 to generate the sample stream of y(n). Then, a decimation block will reduce the sampling rate by a factor of 15 to generate sample stream of z(n). 100MHZ FPGA z(n) Decimator x(t) х(п) y(n) ADC Interpolator LPF1 LPF2 i. When LPF1 (Low Pass Filter 1) and LPF2 are implemented using a 30-taps FIR structure, and the system must operate in streaming way (every samples must be processed without any halt), what will be required FPGA clock frequency and what type of FIR filter structures should be used? Input samples are 12-bits and coefficients are 10-bits for both filters. Determine the number and the size of multiplication and addition operations in FPGA to implement LPF1 and LPF2. Comment on the bit growth and what kind of digital operations should be…
A typical digital signal processing (DSP) system is given in figure below. ADC has 100MHZ sampling clock and every samples will be captured by FPGA for backend processing. An interpolator increases the sampling rate by a factor of 4 to generate the sample stream of y(n). Then, a decimation block will reduce the sampling rate by a factor of 15 to generate sample stream of z(n). 100MHZ FPGA У (n) z(n) Decimator x(t) x(n) ADC Interpolator LPF1 LPF2 When LPF1 (Low Pass Filter 1) and LPF2 are implemented using a 30-taps FIR structure, and the system must operate in streaming way (every samples must be processed without any halt), what will be required FPGA clock frequency and what type of FIR filter structures should be used? Input samples are 12-bits and coefficients are 10-bits for both filters. Determine the number and the size of multiplication and addition operations in FPGA to implement LPF1 and LPF2. Comment on the bit growth and what kind of digital operations should be implemented…
Please , Quickly solve these qualities about autocorrelation non periodic signal
A sinusoid has a period T0 = 3 dt, an amplitude of 1.5 mVolt, and an phase = 15 degrees a. Write down the representation of this signal.b. Perform the sampling process on the above signal with a sampling frequency of Fs = 2 kHz. Write an expression for the sampled sinusoid signal and determine the digital frequency.
What is output signal when a signal x(t)=cos(2*pi*40*t) is sampled with a sampling frequency of 20HZ? a) cos(pi*n) b) cos(2*pi*n) c) cos(4*pi*n) d) cos(8*pi*n)
Two "different" signals with the same sampling interval have the same sample values and z-transformations Describe / explain the situation schematically.
A nonperiodic composite signal has a bandwidth of 170 kHz, with a middle frequency of 120 kHz and a peak amplitude of 20 V. The two extreme frequencies have an amplitude of 10 V. 1. The lowest frequency is KHz. 2. The highest frequency is KHz. Draw the frequency domain of the signal. (You don't need to submit the curve to the Canvas.)
2) A voltage signal consists of the following periodical waveform: V(t) = 10 sin 502.7t + 5 sin 94.2t + 15 sin 942.5t where t is in seconds and Vin volts. This signal is sampled digitally at a sampling frequency of 200 Hz. 128 data points are taken. a) Recommend additional procedures to sample the signal properly in the frequency domain considering the sampling conditions given above. b) Sketch what the frequency spectrum would look like if you were to perform an FFT on these sampled data. Label your axes carefully. c) Calculate: - the total sampling time - the time increment between sampled data points - the frequency resolution of the frequency spectrum - the Nyquist frequency