As a design engineer, you were assigned to produce warning light in hazard compound at UNNM Engineering workspace. It required two input frequencies, 32kHz and 8kHz to operate the running light independently. By using a clock generator value of 128kHz, design a circuit that utilized the JK flip-flops to produce required signal frequency.

As a design engineer, you were assigned to produce warning light in hazard compound at UNNM Engineering workspace. It required two input frequencies, 32kHz and 8kHz to operate the running light independently. By using a clock generator value of 128kHz, design a circuit that utilized the JK flip-flops to produce required signal frequency.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Problem #4: Consider the Programmable Array Logic PAL module below '1' A B C D F₁ F2 F3 1. Determine the corresponding product term per row PRODUCT TERMS 000000
What output does the following multiplexer output? Note: if a line is cut and a number is written, it shows how many bits or how many lines are there. The lines below are 4 bits.
Problem #1: Draw a binary ripple counter that will convert a 128-kHz pulse signal into a 4-kHz square wave.
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
DRAM uses a _______ to store a bit in each cell. A.transistor B.diode C.capacitor D.flip-flop
24. a. The serial adder required six clock pulses to add two, three bit binary numbers. (True or False. Write the correct one, if it's false) b. A three bit parallel adder circuit uses three adders to add all bits on two clock pulse. (True or False. write the correct one, if it's false) c. What is the two's complement of 1001?
Q4) Figure below shows a typical clock-oscillator circuit using a (555 timer) and a (J-K flip-flop). Perform the following: The output frequency from the 555 timer. |(4) 18) R. S6 KO SET Va (7) DISCH our The R INAO (6) (3) OUr 555 (2) TRIG Timer cONr G a01 0.01 AF (decouptng aptonu O 1.9 kHz. 2.1 kHz. 1.8 kHz. 2.0 kHz. The output frequency from J- K flip-flop. * 0.5 kHz. O 1.0 kHz. 1.5 kHz. 2.0 kHz. The HIGH time and LOW time of the 555 timer's output. 378 & 126 micro second. 377 & 126 micro second. 378 & 125 micro second. 377 & 125 micro second.
Q D C Clock and Data Signals are shown for a D-Latch. Sketch the output waveform Q. Assume the propagation delay of the storage elements in negligible. The Initial value of Q is 0.
Study the code below and answer the following questions a. Calculate the total amount of storage required for the program b. Calculate the total number of T-states and time required to execute the program assuming the clock signal frequency is 6MHZ. Show all the steps involved
5- Discuss the effect of changing the number of bits on the recovered analog waveform. 6- Discuss the effect of changing the frequency of input analog signal on the reconstructed analog output signal.
B) (Using Direct method) convert ( 10010001 )BCD to Binary number.