Answer the following questions by referring the given figure: (0.5 material specification + 0.5 mark reason) 1000 A s00 600 B 400 200 0.15 0.30 0.40 Identify the material which is having lowest toughness. Give reason Identify the material with more resilience. Give reason Which material having less hardness? Why?

Answer the following questions by referring the given figure: (0.5 material specification + 0.5 mark reason) 1000 A s00 600 B 400 200 0.15 0.30 0.40 Identify the material which is having lowest toughness. Give reason Identify the material with more resilience. Give reason Which material having less hardness? Why?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Which one(s) of the following about G, shear modulus of elasticity of a material are correct? select all which are correct. G is also called the modules of rigidity. G is related to the modulus of elasticity E and Poisson’s ratio . G is usually smaller than Young's modulus E for the same material. G is the ratio of shear stress to shear strain when the material's proportional limit in shear has not been exceeded.
Mild steel 1 Young;s modulus 1219.5 Yield strain and stress (0.4101,500.08) Failure stress and strain :not able to find because the given data shows the experiment did not reach the failure point. if the material stress and strain does not reach a failure point ,what dose it means , does it means that the material is more stronger?
Given the following stress-strain graph:a. is the modulus of elasticity of "A-514" greater, less or equal to the one of "A-572"?b. from the previous question, make an estimatio for both of them, check that the graphic comes in %c. If we were to test these materials in a universal tension equipment, which one would withstand more load?d. If we were to test these materials in a universal tension machine, which one would elongate the most before fracturing? would elongate the most before fracturing? e. Of the 6 materials shown, do any behave as brittle materials? f.
o (MPa) 900 800 700 600 500 400 300 200 100 0 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 Question 1 Which ONE of the following descriptions is TRUE for this material? Its yield stress is approximately 720 MPa. It is a brittle material. It is a ductile material. Its ductility as a percentage elongation is approximately 0.6%. E
q1: Describe tensile test in detail considering the steps. . define stress , strain (equation and units) . elasticity modulus, elastic and plastic zones . toughness, resilience of matiral Demonstrate stress strain curve for your answer
Q2c) Listed in the table below is the tensile stress-strain data for different grades of steels. Utilizing the data given answer the three queries given below. Tensile Strain at Fracture Strength Strength Fracture Strength Modulus Material Yield Elastic (MPa) (MPa) (MPa) (GPa) А 410 1440 0.63 265 410 200 220 0.40 105 250 C 815 950 0.25 500 610 800 650 0.14 720 210 E Fractures before yielding 650 550 1) Which will experience the greatest percent reduction in area? Why? 2) Which is the strongest? Why? 3) Which is the stiffest? Why? B.
Select All the correct statements from below. a. If the averaged distance between partial dislocations for material A observed under TEM is smaller than material B, the estimated stacking fault energy of material A is lower than material B. b. K_IC is a material property that doesn't change with testing conditions c. The main difference between high cycle fatigue and low cycle fatigue is the difference in the number of cycles to failure d. A negative R value in fatigue test indicate the minimum stress is compressive in nature
Recording Help Stress (MPa) 600 500- 400- 300 200 100- 0 0.00 Tell me what you Exercise 2 Stress (MPa) 0.04 500 400 300 200- 100 0.000 0.002 0.004 0.006 Strain 0.08 Strain 0.12 0.16 0.20 Consider a cylindrical specimen of a steel alloy 10.0 mm in tension. Determine, its elongation when a load of 20,000 N is applied.
Which of the following statements are true? (This question has more than one correct answer) a. You should always apply safety factors when setting a materials specification b. You should always design in small radii of curvature at profile changes c. Crack propagation in ductile materials occurs when the stresses at the crack tip are greater or equal to the yield strength of the material d. The stress concentration factors for ductile materials are greater than expected e. The stress concentration factors for brittle materials are less than expected f. Crack propagation in brittle materials occurs when the stresses at the crack tip are greater or equal to the failure strength of the material
Question 8. The following figure represents three hardness-testing techniques of materials. Describe their specifications, how there are conducted and their potential applications? 8 - Shape of Indentation Test Indenter Side View Top View Load Brinell 10-mm sphere P of steel or tungsten carbide Vickers Diamond 136° microhardness ругamid Rockwell and 60 kg) 100 kg } Rockwell 150 kg) Diamond 120° superficial cone: s - in.- diameter Rockwell 15 kg 30 kg } Superficial Rockwell 45 kg) steel spheres
The following curve is a result of a tensile test. The gauge length was 2 in, and the specimen diameter was 0.505 in The fracture area was round with a diameter of 0.391 in. Remember to com 20000 Force (pounds force) 15000 10000 5000 0 16. The yield strength is 0 0.2% O 80,000 pl O 12.000 p 060,000 pl 85,000 p 0.1 0.2 Extension (inch) 0.3 0.4
Read the question carefully and give me both A&B right solutions otherwise leave it. A) Steel Alloy rod made of Stainless Steel 304 is subjected to 60 kip of Tensile force. Steel rod is having diameter of 1 in. and Length of 8 in. Determine change in its length and diameter. Consider material behaves elastically. For determining material properties use Mechanical property table. B) An aluminium specimen made up of 6061-T6 Material has a diameter of d = 20 mm and a gage length of L0= 300 mm. If a force of 135 kN elongates the gage length 0.9 mm, determine the modulus of elasticity. Also, determine contraction of diameter.