An optical fiber system is to be designed to operate over an 8 km length without repeaters. The rise times of the chosen components are: Source (LED) Fiber: intermodal (pulse broadening) intramodal Detector (p-i-n photodiode) 8 ns 5 ns km-¹ 1 ns km-¹ -1 6 ns From system rise time considerations, estimate the maximum bit rate that may be achieved on the link when using an NRZ format.

An optical fiber system is to be designed to operate over an 8 km length without repeaters. The rise times of the chosen components are: Source (LED) Fiber: intermodal (pulse broadening) intramodal Detector (p-i-n photodiode) 8 ns 5 ns km-¹ 1 ns km-¹ -1 6 ns From system rise time considerations, estimate the maximum bit rate that may be achieved on the link when using an NRZ format.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter15: Experimental Methods

Section: Chapter Questions

Problem 1CQ

See similar textbooks

Similar questions

the most common used infiltrometer A single ring double ring C) tube-type infiltrometer lysimeter
9. For the circuit shown in figure find (a) The resonant frequency o (b) Zin(@) Lin ww ΙΩ ele 9 μF 20 mH 0.12
Question 6 Q6) In an attempt to verify if this law is obeyed by the light from a source the above setup was used. The light intensity I from the light bulb was recorded at various distance r and the observations are shown below. Ar +0.001 m Al= 10.1 W/m2 %3D r(m) 0.400 0.500 0.600 0.700 0.800 I(W/m2) 88.2 56.5 38.2 32.1 22.1 1 (m-2) The theory indicates that the light intensity and the distance are related through the equation: 4tr2 Where P is the power emitted by the source. a) Complete the data table b) Plot the graph of I vs 1/r? c) Determine the slope and the intercept of the graph d) Does the light intensity obey inverse square law? e) Find the power of the source from the slope and compare with the given value of 60 Watts. HTML Editor B IUA A I E E E E x ...
13mm 7my 12m 8m 62 mm gom 3mm Amm Smin 10mm 29mm 5mm brom 5nm 2mm Fnm WHAT IS THE DISTANCE OF THE CENTROID FROM THE X-AXIS b) WHAT IS THE DSTAMCE OF THE CENTROID FROM THE Y- AXIS WHAT IS THE INERTIA ABOUT THE X-AXIS d) WHAT IS THE INERTIAA ABOur THE Y-AXIS? WHAT IS THE INERTIA ABOUT THE CENTROIDAL AXIS PARALLEL TO X- AXIS? WHAT IS THE IHERTIA ABOUT THE CENTROIDAL AXIS PARALLEL TO Y- AXIS?
CE 13mm 7m 12mm gm 62mm amm 3mm Amm Smin 10mm 29mm 5mm bmm 5nm 2mm Fmm 9 WHAT IS THE DISTANCE OF THE CENTROID FROM THE X-AXIS b) WHAT IS THE DSTAMCE OF THE CEMTROD FROM THE Y- AXIS
Given the example vectors use the hamming network to find an examplar that closes to following bipolar input
Civil-Fm
Solve the problem 16-22 in the image given.
An externally focused theodolite being setup. The observed horizontal distance from the center of the instrument up to the face of the rod is 30 m, spacing between the stadia hair at the eyepiece is 0.005 m, difference between the upper stadia hair and lower stadia hair is 1.75 m.b) Determine the length from the center of the instrument to the objective lens
CE. 43mm 7my 12mm gmR 62mm gmm Amm Smin 10mm 29mm 5mm lom 5nim 2mm Fmm q WHAT iS THE DISTANCE OF THE CENTROID FROM THE X-AXIS b) WHAT IS THE DSTAMCE OF THE CEMTROID FROM THE YAX1S C What Is THE INERTIA ABOUT THE XAXIS WHAT IS THE INERTIAA ABOLur THE Y-AXIS
The focal length of a concave mirror is 10 cm and the object distance is 15cm. Determine (a) the image distance (b) the magnification of image (c) the image size of the object is 3cm tall and (d) describe the image formed
find cg and Ix and ly and Ixy loom 40 cm 30cm 200m