An oil having a specific gravity of 0.87 is being pumped from a lower reservoir whose water surface elevation is 150 m througha 200mm diameter suction pipe. It is then discharged through a 200 mm diameter pipe to an elevated reservoir whose water surface elevation is 200m The total head loss during the flow from suction to discharge is 12m of oil. Find the volume flow rate of the oil. Select the correct response(s): O0.12 m2/s 0.24 m /s 0.48 m27s 0 36 m/s

An oil having a specific gravity of 0.87 is being pumped from a lower reservoir whose water surface elevation is 150 m througha 200mm diameter suction pipe. It is then discharged through a 200 mm diameter pipe to an elevated reservoir whose water surface elevation is 200m The total head loss during the flow from suction to discharge is 12m of oil. Find the volume flow rate of the oil. Select the correct response(s): O0.12 m2/s 0.24 m /s 0.48 m27s 0 36 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Water is pumped through three pipes in series. Compute the discharge if the power delivered to the pump is W₂ = 1920 kW and the pump efficiency is n = 82%. The pipe resistance coefficients are R₁ = 13.2 s²/m³, R₂ = 204.1 s²/m³, R₂ = 25.8 s²/m³, and the head difference between the downstream and upstream reservoirs is 50 m. Ans: Q = 0.792 m³/s
An oil having a specific gravity of 0.87 is being pumped from a lower reservoir whose water surface elevation is 150 m through a 200mm diameter suction pipe. It is then discharged through a 200 mm diameter pipe to an elevated reservoir whose water surface elevation is 200m. The total head loss during the flow from suction to discharge is 12m of oil. Find the head added by the pump. Select the correct response(s): 56.98 m 97.23 m 82.23 m 70.45 m P
7) A pump has the following characteristic: Volume flow rate 23 46 69 92 115 (m³/h) Head (m) 17 16 13.5 10.5 6.6 The is used to pump water from a lower tank to a higher tank through a total length of pump 800 m of 150 mm diameter pipe. The difference between the water levels in the two tanks is 8m. Neglecting all losses except friction and assuming that C; = 0.004, find the rate of flow between the two reservoirs. [Ans: = 60m/hr]
An oil having a specific gravity of 0.87 is being pumped from a lower reservoir whose water surface elevation is 150 m through a 200mm diameter suction pipe. It is then discharged through a 200 mm diameter pipe to an elevated reservoir whose water surface elevation is 200m. The total head loss during the flow from suction to discharge is 12m of oil. Find the head added by the pump. Select the correct response(s): 56.98 m 97.23 m 82.23 m 70.45 m
Q1/ Water. p=1.94 slugs/ft' and v=0.000011 ft/s, is pumped between two reservoirs at 0.2 ft/s through 400 It of 2-in-diameter pipe and several minor losses coefficient is(12.2m), as shown in Fig. 1. The roughness ratio is s/d = 0.001. Compute the pump horsepower required. MY (2) Z₂=120ft Z=20 ft Pump Fig.1 D=2 in
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is 2000m and dia. Of 0.8m .Find the rate flow of each pipe if the total flow rate in the main pipe is 0.3 m3/s. the coefficient friction of each pipe is same and equal to 0.05. Ans.Q1= 1.906 m3/s , Q2=1.094m3/s Ex. A pipe of dia.=20cm and length 2000m is connects two reservoir having difference of water levels as 20m determine the discharge through pipe. If an additional pipe of diameter 20cm and length 1200 m is attached to the last 1200m length of the existing pipe, find the increase in the discharge. f=0.015 neglect minor losses. Ans.Q= 0.0254 m3/s , increase to discharge 0.0088m3/s Ex. Pipe of L=4000m and dia.=0.6m as shown in fig. At a distance of 1000m from the upper reservoir , a small pipe is connected to the pipe line. The water can be taken from the small pipe. Find discharge to the lower reservoir a- No water is taken from the small pipe b-100 liter/sec of water is taken from small pipe. f30.005 neglect minor…
m². -5 S Figure shows a portion of a fire protection system in which a pump draws water at 60°F (v =1.21 ×10¯ from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height h of the water level in the tank in order to maintain 5.0 Psig pressure at point A h 25 ft A Pump 2600-ft-long 8-in Schedule 40 steel pipe Flow Flow 45-ft-long 10-in Schedule 40 steel pipe B
1) A smooth steel pipe of diameter 500 mm and length 850 m carry water at the rate of 0.05 m3/sec. Find the head lost due to friction. Take Kinematic Viscosity of water as 0.018 x 10 m2/sec 2)Determine the friction factor, “f” if Ethyl Alcohol at 25 C is flowing at 5.3 m/sec in a standard DN 40 Schedule 80 steel pipe 3)Determine the energy loss that will occur as 100 Liters / min of water flows from a small copper tube to a larger tube through a gradual enlargement having an included angle of 30 degrees. The small tube has a 25 mm OD x 1.5 wall thickness; the large tube has an 80 mm OD x 2.8 mm wall thickness.
Water enters a pump through a 250mm diameter pipe at 35 kPa. It leaves the pump at 140 kPa through a 150mm diameter pipe. If the flow rate is 150L/s. Assume suction and discharge side of the pump to be of the same elevation. Compute the velocity of discharge pipe. Select the correct response: 6.66 m/s 8.49 m/s 7.45 m/s 9.23 m/s
Question 5: The pump shown below delivers a head of 50 m to the water through 30 cm diameter with pipe length 500 m. If the head loss is given by determine. L V² 0.02 / 1. The flow rate (Q) through the system in m³/s 2. The input power (Pi) required to supply the pump if the efficiency=75% 2 40 m L w **** AVB
5. 10 lt / s of water is requested to be transported from A depot to city B. The water level of the A depot is 50 m and the B point is 30 m. The length of the EU pipe in the project has been calculated as 1000m and taken as f = 0.02. The pipe diameter has been chosen as φ90 mm. Since the minimum operating pressure (pressure head) required at point B is 20m, can water be delivered to point B with this system? (Velocity height is negligible)