20. In a repair shop compressed air is used to operate pneumatic tools. The total length of the airline including all the loss coefficients in terms of equivalent length is about 152.5 m (500 ft). The airline consists of smooth pipe of I.D. = 1.27 cm. Air is compressed to 0.345 MPa (50 psia) and then cooled to 24 C (75 F) when entering the line at a velocity of 2.4 m/s (8 ft/s). Find pressure when air is used to operate the pneumatic tool. %3D - To Pneumatic tool Air intake Compressor

20. In a repair shop compressed air is used to operate pneumatic tools. The total length of the airline including all the loss coefficients in terms of equivalent length is about 152.5 m (500 ft). The airline consists of smooth pipe of I.D. = 1.27 cm. Air is compressed to 0.345 MPa (50 psia) and then cooled to 24 C (75 F) when entering the line at a velocity of 2.4 m/s (8 ft/s). Find pressure when air is used to operate the pneumatic tool. %3D - To Pneumatic tool Air intake Compressor

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The inlet pressure to a piping system is 440 kPa. The inlet pipe diameter is 0.6 m. What is the velocity of the flow of water and discharge at the inlet?
The velocity and pressure at the entrance to a horizontal pipe are 1 m/s and 120 kPa respectively The velocity and pressure at the exit of the pipe are 1.8 m/s and 100 kPa respectively. What is the head loss (h) between the entry and exit of the pipe? 1.81 m a. 192 m b. 2.14 m 2.03 m Od. The velocity and pressure at the entrance to a horizontal pipe are 0.7 m/s and 101040 Pa respectively. The velocity at the exit of the pipe is 1.6 m/s. What is the pressure at the exit of the pipe? 100 kPa O a 99.52 kPa 101.26 kPa O c. 102.57 kPa d.
The maximum velocity of an air flow (v= 700 ms-1 and T=160 oC
A fan draws 1.42 m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan mechanical is 70% and air is measured at 25 0C and 760 mmHg. Using p water formulaPw=
Two opened tanks filled with water are connected by seriel pipe AB and BC. AB pipe has a diameter of 10cm, and BC pipe is 6cm. The length of pipe for AB is 200m and for pipe BC is 150m. The flow rate of water entering the pipe is 0.007m³/s and coefficient of contraction is 0.62. If the energy losses ONLY occur due to the shock loss at sudden contraction and friction, calculate the level difference of the two tanks. Given f = 0.04 for both pipes.
D=6.1 mmdetermine flow rate in l/s
Water at 15 degrees Celsius is flowing through a 2-in ID smooth pipe. The friction loss for a 100-ft section of the pipe amounts to 4.8 lbf/lbm. Determine the velocity of the flow.
A pump is being used to transport a liquid food product (density p=1000kg/m^3, viscosity 0.001 Pa s) from holding tank to filling a machine at a mass flow rate of 2 kg/s. The liquid level in the holding tank is 10 m above the pump, and the filling machine is 5 m above the pump. There is 100 m of 2-in nominal diamter sanitary pipe between the holding tank and the filling machine, wiht one open globe valve and four regular 90° flanged elbows in the system. Within the system, there is a heat exchange which causes 100 kPa of pressure drop due to friction. The holding tank is open to atmosphere, and filling machine is running at a pressure of 1.5 atm. The diamter of the filling machine pipe is 3cm. A: What is the volume flow rate of the system? B: What is the diamete of the pipe? C: What is the average velocity inside the pipe? D: What is the reynolds number of the flow in the pipe? E: What is the flowing type?
Air is kept in a tank at pressure Po= 689 KPa abs and temperature To = 17°C. If one allows the air to issue out in a one-dimensional isentropic flow, the flow per unit area at the exit of the nozzle where P = 101.325 KPa is Blank 1 kg/m²-s. For air, Use R = 287 J/kg-K and Mol. Wt. = 29.1 *Express your answers in whole significant figure without decimal value and without unit*
Determine the velocity of the flow of water @45C is flowing through a 3-in ID smooth pipe. The friction loss for a 75 ft section of the pipe amounts to 2.4 lbf / lbm.
A sudden enlargement in a circular duct measures 0.20 m diameter upstream and 0.40 m downstream. The upstream pressure is 150 Pa, the downstream pressure is 200 Pa. Determine the flow rate of 20°C air through the fitting, if density is 1.2041 kg/m3. Group of answer choices 0.58 m3/s 0.38 m3/s 0.28 m3/s 0.48 m3/s
The water needs of a small farm are to be met by pumping water from a well that can supply water continuously at a rate of 50 L/min. The water level in the well is 13 m below the ground level, and water is to be pumped to the farm by a 2-cm internal diameter pipe. The required length of piping is measured to be 20 m, and the total head loss in the piping system is estimated to be 10 m.a) Using Bernoulli equation, determine the pressure difference between the two points (A & B).