An external turning operation is performed on a hollow workpiece of 200 mm external diameter and 100 mm inner diameter, at 40 m/min cutting speed, 2 mm depth of cut and 0.20 mm/rev feed. Calculate: The rotational speed for this workpiece. The machining time needed for a length of 250 mm. The material removal rate used.

An external turning operation is performed on a hollow workpiece of 200 mm external diameter and 100 mm inner diameter, at 40 m/min cutting speed, 2 mm depth of cut and 0.20 mm/rev feed. Calculate: The rotational speed for this workpiece. The machining time needed for a length of 250 mm. The material removal rate used.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 600mm*30mm flat surface of a plate is to be finish machined on a shaper .The plate has been fixed with 600 mm side along the tool travel direction. If the tool over-travel at each end of the plate is 20 mm, average cutting speed is 8 m/min, feed rate is 0.3 mm/stroke and the ratio of return time to cutting time of the tool is 1:2 Determine time required for machining?
In turning of stales steel alloy, 1100 mm length and 400 mm diameter, the Feed was 0.35 mm/rev, and depth of cut = 2.5 mm. The tool used in this cutting is cemented carbide tool where Taylor tool life parameters are n = 0.24 and C = 450 (tool life (min) and cutting speed (m/min). Compute the cutting speed that will allow the tool life to be 10% longer than the machining time for this part.
Q1. Calculate the time required to machine a workpiece 170 mm long, 60 mm diameter to 165 mm long 50 mm diameter. The workpiece rotates at 440 rpm, feed is 0.3 mm/rev and maximum depth of cut is 2 mm. Assume total approach and overtravel distance as 5 mm for turning operation. Answer Q2. A gray cast iron surface 280 wide and 540mm long may be machined either on a vertical milling machine, using a 100mm - diameter face mill having eight inserted HSS teeth, or on a horizontal milling machine using an HSS slab mill with eight teeth on a 200-mm. diameter. Which machine has the faster cutting time? The values of feed per tooth and cutting speed for both processes are 0.4mm/tooth and 80m/min, respectively. The depth of cut = 3.0 mm and assume A and O equal to 5. Answer
In a turning operation, the workpiece diameter is Dm=44.00 mm and the diameter after the operation should be 22.00 mm. The cutting speed is set to 105.00 m/min and the federate is 0.03 mm/rev. Calculate the material 3 removal rate (Cm²Imin) for this operation (Do not input units). Your Answer: Answer
In an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel bar. Spindle speed is 300 rpm and a feed rate of 0.25 mm/rev is given to the tool. Produced chips have a width of 2 mm. Calculate the material removal rate at the beginning and at the end of the cut. Can u help me please?
Q3). A block of 190mm length and 100mm width is to be machined in shaping process. The permissible cutting speed is 30m/min. maximum quick return ratio is 3:2 at the design value of stroke of 400mm. Calculate the time of machining of the block, assuming total depth of cut to be 8mm, L=1₂+1+1, 40+190+20=250mm, B=ba+b+bo=10+100+10=120mm?
Plate 200 mm x 90 mm is to be maintained on a shaper under following condition, v= 13.5 m/ min Feed is 0.57 mm/ double stroke, Approach and overtravel 20 mm each in longitudinal direction and 4 mm each in lateral direction. The ratio of cutting to the return speed is 0.83.Calculate the machining time in minutes?
In orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool. the cutting velocity is 90 m/min The feed is 0.24 mm/rev and the depth of cut is 2 mm. The chip thickness obtained is 0.48 mm If the orthogonal rake angle is zero and the principal cutting edge angle is 90° Calculate the shear angle in degree.
A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.
In a production turning operation, the workpart is 60 mm in diameter and 500 mm long. A feed of 0.75 mm/rev is used in the operation. If cutting speed-9 m/s, the tool must be changed every 4 workparts; But if cutting speed=5 m/s, the tool can be used to produce 50 pieces between tool changes. Determine the Taylor tool life equation for this job. (use the equations given below for solution) L Tm- 1,= Nf N AD, vT" = C %3| AD,L Tm fv
The following data is given for slab milling of a 300 mm long 50 mm wide mild steel block: Cutter of diameter= 60 mm; Numbers of teeth =12; Cutter speed = 120 rev/min; Depth of cut = 3.2 mm; Feed is 0.25 mm/tooth.Determine (i) Table feed in mm/min, (ii) MRR (iii) Power (iv) Torque and (v) Total machining time. Assumesuitable approach and over-run and specific energy of mild steel as 5 Ws/mm3.
The end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an outside diameter of 38.0 in and an inside diameter of 24.0 in. If the facing operation is performed at a rotational speed of 40.0 rev/min, feed of 0.015 in/rev, and depth of cut of 0.180 in, determine (a) the cutting time to complete the facing operation and the cutting speeds and metal removal rates at the beginning and end of the cut.