A mild steel block of width 40 mm is beingmilled using a straight slab cutter70 mm diameter with 30 teeth. If the cutterrotates at 40 rpm and depth of cut is 2 mm,determinethe value of maximum uncut chip thicknesswhen the table feed is 20 mm / min.

Answered: Image /qna-images/answer/be6bc545-5fab-429e-bd94-0a6e518faa28.jpg

Answered: A mild steel block of width 40 mm is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The face milling cutter of D = 200 mm used to cut a block which is 200 mm H, 1=480 mm, if f- 0.7 mm/rev is used and the overrun of the cutter is 12 mm and cutting speed 320 mm/min. Calculate the machining time. Cuttin
A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine lathe at the following cutting conditions: cutting speed = 400 ft/min, feed = 0.015 in/rev, and depth of cut = 0.150 in. Determine the time to complete one turning pass if the approach and overtravel allowances are each 0.25 in (total = 0.50 in). Note: 1 ft = 12 in
across the surface and (b) the maximum metal removal rate during cutting A slab milling operation is performed on the top surface of a steel rectangular workpiece 12.0 in long by 2.5 in wide. The helical milling cutter, which has a 3.0 in diameter and ten teeth, is set up to overhang the width of the part on both sides. Cutting speed is 125 ft/min, feed is 0.006 in/tooth, and depth of cut = 0.300 in. Determine (a) the actual machining time to make one pass across the surface and (b) the maximum metal removal rate during the cut. (c) If an additional approach distance of 0.5 in is provided at the beginning of the pass (before cutting begins), and an overtravel distance is provided at the end of the pass equal to the cutter radius plus 0.5 in, what is the duration of the feed motion.
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes
It is required to reduce the thickness of cast iron workpiece with dimensions (L x w x t) of (230 mm x 120 mm x 25 mm) to 22 mm using shaper machine. Given that average cutting speed is 21 m/min, feed 1.2 mm/double stroke, and return/cutting time ratio is 3/4. The approach at each end is 72 mm. If the permissible depth of cut is 2 mm, determine the cutting time in the following cases: i) Using shaper with a mechanically driven ram. ii) Using shaper with a hydraulically driven ram. Solution: i) Mechanically ( ii) Hydraulically
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 49 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.2 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 4mm (iii) Total time required to complete the turning operation is 52.6 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpm
A cylindrical rod is machined using turning processes. It is given that the cutting speed is 120min ¹, and feed per tooth is 0.0025 m/min. The outer diameter is 35mm, the length of the rod is 130m and the inner diameter is 22mm. The number of teeth is 6. Find Rotational speed, Feed rate, Machining time, and Depth of cut.
Calculate the time required for completing a 5mm deep finishing cut on a 150mm wide, 600mmlong face of a 25mm thick steel block using a face milling cutter of 150mm diameter with 6teeth. The cutting condition are Vc =1.5m/sec and fz = 0.1mm.
A two-spindle drill cuts two holes at the same time, one 1/2 inch and one 3/4 inch. The workpiece is 1.0 inches thick. Both drills have point angles of 118 degrees and the cutting speed for the material is 300 ft/min. The rotational speed of each drill can be set individually but the feed rate for both holes must be set to the same value because they move together into the material. The feed rate is set so that the total metal removal rate of both drills combined does not exceed 1.50 in3/min. Determine (a) maximum feed rate (in/min) that can be used, (b) individual feeds (in/rev) for each hole, and (c) cutting time for the operation.
H.W. The face milling cutter of D= 200 mm used to cut a block which is 200 mm = H, 1=480 mm, if f= 0.7 mm/rev is used and the overrun of the cutter is 12 mm and cutting speed 320 mm/min. Calculate the machining time.
A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.3 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 6 mm, over run length is 3mm (iii) Time required to complete one single turning operation is 2.3 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes (c) Spindle speed in in rpm (d) Cutting speed in m/minutes

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A mild steel block of width 40 mm is being milled using a straight slab cutter 70 mm diameter with 30 teeth. If the cutter rotates at 40 rpm and depth of cut is 2 mm, determine the value of maximum uncut chip thickness when the table feed is 20 mm / min.