An aluminum cylinder and a bronze cylinder are centered and secured between two rigid slabs by tightening two steel bolts as shown. At 50° F no axial load exists in the assembly. Find the stress in each material at 200° F. Area (sq. in.) E (psi) a (in./in/°F) Aluminum 2.0 10 x 106 12.8 x 10-6 3.0 12 x 106 10.5 x 10-6 Bronze Steel 0.75 29 x 10° 6.5 x 10-6 -|| 3"- + ET Alum. Bronze 41 It 11 11 enn

An aluminum cylinder and a bronze cylinder are centered and secured between two rigid slabs by tightening two steel bolts as shown. At 50° F no axial load exists in the assembly. Find the stress in each material at 200° F. Area (sq. in.) E (psi) a (in./in/°F) Aluminum 2.0 10 x 106 12.8 x 10-6 3.0 12 x 106 10.5 x 10-6 Bronze Steel 0.75 29 x 10° 6.5 x 10-6 -|| 3"- + ET Alum. Bronze 41 It 11 11 enn

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Estimate the transverse tensile strength of the concrete in Problem 12.6.
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
4. For the rods shown, determine (a) the compressive force after a temperature rise of 95°C, (b) the corresponding change in length of the aluminum rod. 0.5 m Aluminum A = 2.0x10-3 m2 E 70 GPa a= 23x10-6/Oc + 0.3 m Bronze A = 1.5x10-3 m2 E = 110 GPa d=18x10-6/0c .0 mm
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
= H.W A Solid Steel bar of diameter 60mm and length 350 mm is placed inside an aluminum cylinder of inside diameter 70mm and out side diameter Ilomm, a compressive load of looo la is applied on the assembly, find the stresses in the bar and the cylinder? take Est = 200 GPa and EA1 = 70 G Pa. P=1000k Cover Plate 0.25mm dif do 350mm Alum, cylinder Steel bar
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)