Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 50 kN/m 0.8 m B -24 m- 0.8 m For the selected design, determine the actual value of om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.

Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 50 kN/m 0.8 m B -24 m- 0.8 m For the selected design, determine the actual value of om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Maxinnun allowable stress for steel - 140 MPa Maxinnum allowable stress for ahuminum = 90 MPa Maxinnun allowable stress for brouze - 100 MPa Required: Maximun safe value of axial load P Aluminum A 400 mm Bronze A= 200 mm Steel A= 500 mm 2P 4P 2.5 m 2.0 m 1.5m
The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress acting on section a–a in MPa What is the shearing stress acting on section a–a in MPa The lapbelt assembly is to be subjected to a force of 800 N. What is the required thickness t in mm. of the belt if the allowable tensile stress for the material is 10 MPa?
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
Assume the transformed steel section reaches its allowable bending stress first. Calculate the magnitude of the allowable bending moment that can be applied in this case. Answer: M- i Ib-in.
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
1.(e) The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests. It has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑Y 40 MPa 80 MPa 25 MPa
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check