A part made from hot-rolled AISI 1212 steel undergoes a certain amount of cold-work operation. If the ultimate strength of the material after cold work operation was 80 kpsi. (a) Determine the percentage of cold work (b) Obtain the yield strength after the cold work (c) Determine the hardness of the material before and after the cold work operation

A part made from hot-rolled AISI 1212 steel undergoes a certain amount of cold-work operation. If the ultimate strength of the material after cold work operation was 80 kpsi. (a) Determine the percentage of cold work (b) Obtain the yield strength after the cold work (c) Determine the hardness of the material before and after the cold work operation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

part made from AISI 1212 steel undergoes a 20 percent cold-work operation. (a) Obtain the yield strength and ultimate strength before and after the cold-work operation. Determine the percent increase in each strength. (b) Determine the ratios of ultimate strength to yield strength before and after the cold work operation. What does the result indicate about the change of ductility of the part?
A mild steel material is subjected to a Brinell hardness test with an applied force of 7459 N using a hardened steel ball indentor of 11 mm and it is found that the Brinell Hardness Number as 954. Determine the surface area of indentation and indentation diameter. (NOTE: Please Solve the problem in a paper and upload in the separate submission link provided and also fill the answers without the unit in the box below) i) Surface Area of Indentation (in mm?) -- ( ii) Indentation Diameter (in mm)
Determine the indentation diameter of a mild steel material subjected to a Brinell hardness test with a test force of 8.1 kN using a hardened steel ball indentor of 10 mm. Take the Brinell Hardness Number as 926. Also, determine the surface area of indentation. (NOTE: Please Solve the problem in a paper and upload in the separate submission link provided and also fill the answers without the unit in the box below) i) Indentation Diameter (in mm) -- ii) Surface Area of Indentation (in mm?)
Problems 1. A Rockwell hardness measurement is made on a ductile iron (80-55-06 as cast) and the obtained Rockwell hardness R scale is 13 HRC. Predict the tensile and yield strengths of this material. 2. A Brinell hardness measurement is made on a ductile iron (120-90-02, Oil-quenched) using a 10-mm-diameter sphere of tungsten carbide. A load of 3,000 kg produces a 3.52-mm- diameter impression in the iron surface. a. Calculate the BHN of this alloy. (The correct units for the Brinell equation are kilograms for load and millimeters for diameters.) b. Predict the tensile and yield strengths 3. Suppose that a ductile iron (100-70-03, air-quenched) has a tensile strength of 800 MPa. What diameter impression would you expect the 3,000-kg load to produce with the 10-mm- diameter ball? Search LO W SE
An application requires ultimate tensile strength and yield strength ofa steel at 110 ksi and 91 ksi, respectively. Answer the following 4 questions: Can SAE 1040 steel be selected for this application? If “no” is the answer in Part I, the following Part II, III, and IV can beignored. If “yes” is the answer in Part I, which condition of SAE 1040 shouldbe selected? Why is that steel with the condition in part II selected? Is the selected steel brittle or ductile? and Why?
A Cu-30% Zn brass plate, originally 1.20 inches thick, is desired to have a yield strength greater than 50,000 psi and a percent elongation of at least 15%. The final geometry of the plate will be obtained by means of cold work. What range of final thicknesses is possible to obtain under the given conditions? The effect of percent cold work on Cu-3096 Zn brass properties is shown below. 100 80 Resistencia a la tensión (ksi) 60 Límite elástico (ksi) 20 Porcentaje de elongación 20 40 60 80 Porcentaje de trabajo en frío Propiedad
An application requires ultimate tensile strength and yield strength ofa steel at 110 ksi and 91 ksi, respectively. Answer the following 4 questions:4.1. Can SAE 1040 steel be selected for this application?4.2. If “no” is the answer in Part I, the following Part II, III, and IV can beignored. If “yes” is the answer in Part I, which condition of SAE 1040 shouldbe selected?4.3. Why is that steel with the condition in part II selected?4.4. Is the selected steel brittle or ductile? and Why?
A hot rolled AISI 1212 steel is given a cold work of 20 percent. Determine the new values of the yield strength and the ultimate resistance.
A non-cold-worked cylindrical rod with an initial length of 800 mm and diameter of 15 mm is to be deformed using a tensile load of 45 kN. Of the materials listed below, which are possible candidates if you assume that failure of the system occurs when the rod plastically deforms? Do the possible candidates change if you change your assumption to the system failing at the onset of necking in the rod? Justify your choice(s). Material Young’s Modulus (GPa) Yield Strength (MPa) 1040 Steel UTS (MPa) Elongation (%) 680 205 440 25 Brass 100 185 310 68 Сopper 125 160 220 44
Q2) Cylindrical rod with original diameter (12mm) and original length (70 mm) made of 1020 Hot-rolled steel alloy which their yield stress (207 MPa) and Young modulus (210 GPa). Tensile test was carried on this rod and it's broken under (27.5 KN) force with final diameter (10mm) and final length (84 mm). Calculate: (A) 1- Engineering fracture stress (B) If you know that the Brinell hardness for this alloy (HB=111). Estimate the tensile strength of this alloy in (MPa). 2- True fracture stress. (C) 1- Toughness gauge. 2- The percentage of elongation.
Tutorial Problem 3 The following data are obtained from the Charpy impact test of a copper specimen. a) Length of the square cross-section specimen = 70 mm b) Each side (top & bottom) of the cross-section = 9.64 mm c) V – Notch thickness at middle of the specimen length = 1.06 mm d) Impact Strength = 279 kJ/m² Determine the Cross-sectional area at the top surface, Cross-sectional area at notch & Impact energy of the copper specimen.
A shear pin made from a 4340 steel (0.4% C) fails by ductile fracture. It was supposed to be initially normalised, austenitised, quenched and tempered to 100% martensite to give a hardness of 5.5 GPa. The hardness was measured to be 4.5 GPa. Which of the following summaries most accurately accounts for what may have gone wrong? O Insufficiently heating the steel would result in partial austenitisation, leading to only partial martensite after quenching and a reduction in final hardness. The temper could still occur at the correct conditions and still lead to an insufficient strength and encouraging ductile failure. O Performing a full austenitisation but then cooling slower than the critical cooling rate for the alloy would allow some ferrite/pearlite to form after the martensite reaction has finished. This would be softer than the tempered martensite and so reduce the final hardness. O Assuming a full austenitisation and then cooling faster than the critical cooling rate, the hardness…