Among the following which statement or statements are True? Select one or more: The difference in the transmission delay between the fastest and slowest pairs of the same un-twisted pair cable is called Delay skew The difference in the propagation delay between the fastest and slowest pairs of the same un-twisted pair cable is called Delay skew The difference in the propagation delay between the fastest and slowest pairs of the same twisted pair cable is called Delay skew The difference in the propagation delay between the fastest and slowest pairs of the same un-twisted pair cable is called Delay distortion

Among the following which statement or statements are True? Select one or more: The difference in the transmission delay between the fastest and slowest pairs of the same un-twisted pair cable is called Delay skew The difference in the propagation delay between the fastest and slowest pairs of the same un-twisted pair cable is called Delay skew The difference in the propagation delay between the fastest and slowest pairs of the same twisted pair cable is called Delay skew The difference in the propagation delay between the fastest and slowest pairs of the same un-twisted pair cable is called Delay distortion

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.3P: A transmission-line cable with a length of 2 km consists of 19 strands of identical copper...

See similar textbooks

Similar questions

1)What is a twisted pair cable?What are its two types and draw the sketch?
Write about the uses and importance of twisted pair cable - crossover cable
What are two advantages of using twisted pair cabling over coaxial cabling on a network? a. Twisted pair cable is more reliable. b. Twisted pair cable is less expensive. c. Twisted pair cable is more resistant to noise. d. Twisted pair cable is more resistant to physical damage. e. Twisted pair cable is required for modern transmission standards.
What is load curve
1 - Why make two wire, three wire or four wire connection in RTD connection?A) To be a backup connection lineB) To increase the magnetic fieldC) Because the resistance of the long connecting wires causes errorD) To increase the costE) For better cooling
Calculate the self-GMD of stranded wire with 2 strands. a. Radius of each strand is 0.001 inch. b. The radius is doubled.c. The radius is halved
5.a.Which organization determines allowable maximum fill ratios for different cables?A. IEEEB. IECC. ANSID. NEC5.b. When should corner pull boxes be used in an installation?A. At all 90 degree bendsB. At all bends less than 90 degreesC. At all bends greater than 100 degreesD. At all bends
The ---_characteristi cs shows the relation between the generated e.m.f at no load and the field current. O a. internal b. non-magnetic C. external d. magnetic
b) Write any 4 advantages of coaxial cable over shielded twisted pair?
b) A fault occurs at bus 3 of the network shown in Figure Q4. Pre-fault nodal voltages throughout the network are of 1 p.u. and the impedance of the electric arc is neglected. Sequence impedance parameters of the generator, transmission lines, transformer and load are given in Figure Q4. V₁ = 120° p.u. V₂ = 120° p.u. V₂ = 1/0° p.u. V₂= 120° p.u. jXj0.1 p.u. JX2) 0.1 p.u. jX0j0.15 p.u. jXn-j0.2 p.u. 1 JX(2)-j0.2 p.u. 2 jX)=j0.25 p.u. JX20-10.15 p.u. jXa(z)-j0.2 p.u. 4 jX2(0)=j0.2 p.u. jXT(1) j0.1 p.u. jXT(2)=j0.15 p.u. jXT(0)=j0.1 p.u. Figure Q4. Circuit for problem 4b). = jXj0.1 p.u. j0.1 p.u. - JX(2) JXL(0) 10.1 p.u. = (i) Assuming a balanced excitation, draw the positive, negative and zero sequence Thévenin equivalent circuits as seen from bus 3. (ii) Determine the positive sequence fault current for the case when a three- phase-to-ground fault occurs at bus 3 of the network. (iii) Determine the short-circuit fault current for the case when a one-phase- to-ground fault occurs at bus…
Q4/ (A) What is the voltage measurement Vx-y , for the circuit shown below. 4v 4v 20 50 y
4. What do you mean by transformer connection Ydl and Dy11?