Q.3) An electrical motor located at A operates at a frequency of 25 Hz and suppliespower to the gear system shown below to run a machine located at F. Thediameters of the shafts are: DAB = 20 mm, DcD = 15 mm and DeF = 30 mm. Theallowable shear stress in the shafts is 60 MPa. Determine the maximum powerthat can be transmitted through this gear system.150 mm150 mm-60 mm60 mm

Answered: Image /qna-images/answer/28012815-ca20-4ddf-a3cf-d514f92d2789.jpg

Answered: allowable shear stress in the shafts is…

allowable shear stress in the shafts is 60 MPa. Determine the maximum power that can be transmitted through this gear system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The module and the number of teeth on the pinion of a spur gear are 12mm and 15teeth respectively.A power of 400kW is to be transmitted at 1700rpm of width.if the involute teeth are of standard proportions (addendum=m) with the pressure angle of 22.5° determine (A) torque due to power delivered (B) tangential load (C) teeth width (E)load on the bearings
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel -20KW JOKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O f segment Co is to be replaced lay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
Spur gear train is used to transmit the power of 2kW from input gear A rotating at 120 rpm to output gear D through a compound gear BC. The number of teeth on the gear A, B, C and D are 16, 32, 12 and 18 respectively. Given: Module = 4mm, pressure angle=20° The tangential force acting on the gear B is N A D В
In a broaching machine shown, shaft A carries a pulley 60.96 cm in diameter which is driven by a leather flat belt from 12-inch pulley on the 30 Hp-squirrel-cage, compensator-motor shaft overhead, the latter turning 1200 rpm. Gears 2 & 4 have 12 teeth each, and 3 & 5 have 60 teeth each. Gear 5 is fast to 6, which has 10 teeth and a module of 8.465 mm/tooth and which engages with rack 7 to which is attached the broach. Assuming that there is no slipping between the pulleys and the belt. Determine: a) the speed with which the broach is drawn through the work, in m/s. b) Specify a double ply, medium weight, cemented joint leather flat belt, considering a mildly jerking loads and a center distance of 60 inches. c) Determine the belt tensions of the belt and the F, maximum stress in the straight part of F₁ ALBA belt if = 3 F₂ Gear 5 Gear 6 Gear 2 DEO CEC A HH₂ Rack 030-0=0 Gear 4 Gear 3
A shaft is fixed at support C and has a torque of 75lb.ft with respect to free end at a distance of 0.75ft from C. It remains constant for 0.75ft before a negative uniformly distributed torque of 1200lb.ft/ft at a distance of 1.5ft is introduced. The shaft then remains flat for 1.5ft to free end with a torque of 600lb.ft. where in the shaft is the torque equals to negative 1200lb.ft measured from the free end?
In a gearbox, a spur gear is mounted on a shaft at equal distances from twosupporting bearings. The shaft and mounted gear turn together at a speed of3600RPM. The gearbox is designed to transmit a maximum power of 3kW. Thegear contact angle is φ = 20°. The pitch diameter of the gear is dp = 30 in. a) Findthe radial force on each of the two bearings supporting the shaft.The ratio of the two bearings’ length and diameter is L/D = 0.5. The bearings aremade of acetal resin material with the following limits:Surface velocity limit, V, is 5m/s.Average surface-pressure limit, P, is 7 MPa.PV limit is 3000 psi-ft/min.b) Find the diameter of the shaft in order not to exceed the stated limits.
The steel shaft with two different diameters rotates at 4.9 Hz. The power supplied to gear C is 54.1 kW, of which 26.9 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 55.5 mm, h = 68.9 mm, L = 4.2 m, M = 2.8 m, and G = 83.46 Gpa. Round off the final answer to two decimal places.
(4) The shaft of a speed reducer is mounted on bearings 200mm apart. A 125mm gear is mounted in between bearing which receives 4kW @ 120rpm. It is known that the shaft have of Sas (allowable stress) = 45MPa; Su = 425MPa; Sy = 240MPa; Sys = 170MPa. Determine the shaft required.
The steel shaft with two different diameters rotates at 4.5 Hz. The power supplied to gear C is 51.7 kW, of which 30.4 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 57.3 mm, h = 68.9 mm, L = 4.2 m, M = 2.4 m, and G = 83.16 Gpa. Round off the final answer to two decimal places. A d Bh C | — L M →
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm². A0a& ENG 1222/20 nere to search
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 if its gearbox 5th gear is selected. The gear's teeth are of involute form with a module of 8 mm, an addendum is double the module, and the pressure angle is equal to 20°. 1.1. If the driving shaft of the front wheels of the truck is connected to the output shaft of the gearbox, determine the number of teeth on the pinion to avoid interference and the corresponding number of teeth on the gear wheel. 1.2. Calculate the gear maximum velocity of sliding.