A vertical piston-cylinder device contains water and is being heated on top of a range. During the process, 85 Btu of heat is transferred to the water, and heat losses from the side walls amount to 12 Btu. The piston rises as a result of evaporation, and 5 Btu of work is done by the vapor. Determine the change in the energy of the water for this process. *

A vertical piston-cylinder device contains water and is being heated on top of a range. During the process, 85 Btu of heat is transferred to the water, and heat losses from the side walls amount to 12 Btu. The piston rises as a result of evaporation, and 5 Btu of work is done by the vapor. Determine the change in the energy of the water for this process. *

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

determine the entr0py change 0f 1.5 moIes 0f amm0nia that is heated fr0m 180°Cto750°C. The system 0perates at an atmospheric pressure on a steady fIow process.
Skg of Steam at pressure of 4.9 bar is produ- ced from water at 20c. Determine the amount of heat supplied if the Steam is o.9 dy.
Calculate the change in internal energy of air with a temperature increase from 400 K to 700 K assuming that specific heat is evaluated at teh average temperature, and specific heats vary with temperature. Report your answer to one decimal place.
Air is contained in a piston cylinder arrangement shown in the figure. Initially the air is200 kPa and 20 oC while the piston rests on the lower stops. The air is heated, and thepiston starts to rise freely when the pressure reaches 250 kPa until the piston start toencounter a linear spring when the volume is doubled. Heat is further added until the airtemperature reaches 1000 oC when the volume is triple the initial volume. Considering airas ideal gas:a- What is the final pressure?b- Find the specific work done during the whole process.c- Draw the process on a p-v diagram indicating the properties at all states
At given temperature, why pressure of water vapors in the superheated region is lower thanthe saturated pressure of water. Explain it with PV or PT diagram.
A piston-cylinder set up contains 0.015 kg of an ideal gas at a volume of 1 liter, a temperature of 5.5 degrees Celcius, and a pressure of 685 kPaa. The gas is heated at constant pressure to 1.75liters. If the total heat input for the process was 2.78 kJ, Find: а. Ср b. R c. Cv
A weighted piston (total masa of 17 kg)., resting on stops in a cylnder (radius of 0.05 m) divides a container into two regions. 0.075 kg of saturated liquid water at 50 Cis contained beneath the piston. The rest of the cylinder and container is evacuated. Heat is applied to the water until the piston is lifted off of the stops and moved a distance () of 0.6 m. As the piston reaches the mouth of the cylinder, the hermetic seal is broken and the cylinder contents can now expand to fil the remainder of the evacuated space. At this instant, no additional heat is added to or removed from the system. When the system fully equilibrates, its absolute pressure is measured to be 0.01 MPa vacuum y -E Cre 20 What is the state of the water when the piston begins to rise off of the stops? ? bị What is the water temperature when the piston reaches the mouth of the cylinder? c) What is the final volume of the water (after the seal is brokenj?
A piston-cylinder device contains 0.91 kg of refrigerant-134a at –10°C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 15°C. Use data from the tables. R-134a -10°C Problem 03.030.b - Change of volume of cylinder with refrigerant Determine the change in the volume of the cylinder of the refrigerant-134a if the specific volume and enthalpy of R-134a at the initial state of 90.4 kPa and -10°C and at the final state of 90.4 kPa and 15°C are as follows: 1= 0.2418 m3/kg, m = 247.77 kJ/kg v2 = 0.2670 m3/kg, and h2 = 268.18 kJ/kg The change in the volume of the cylinder is ]m³.
A piston cylinder device is equipped with a paddle-wheel driven by an external motor andis filled with gas. The walls of the cylinder, the piston, and the paddle-wheel and its shaft areall made of a material which is very good insulator. The system contains 50 g of gas.Initiallythe gas is in state A. The paddle-wheel is then operated, but the piston is allowed to move tokeep the pressure constant. Then the paddle-wheel is stopped, and the system is found to bestate B. There is very little friction between the piston and cylinder walls. Determine the energytransfer in joules along the paddle-wheel shaft. State A B P, bars 35 35 v, m3/kg 7.11 19.16 u, J/g 22.75 47.64 h/ J/g 47.64 164.69
Water in piston cylinder system at (T1 and X1). The water is heated isothermally until the (V2=4V1). Then the work is exchanged with system according the low (PV2 =C) until reach to its original pressure. and draw the processes on P-v diagram and determine 1- The final volume 2- The amount of work
Refrigerant 134a is stored inside an uninsulated ridged tank and heated by an electric resistor for 5 minutes. The temp goes from -10 degrees Celsius to 40 degrees Celsius. The refrigerant has a quality of .8 and the tank has a volume of .01m^3. The electrical resistor is powered by a 12V battery with a current of 5 amps. How much energy is lost from the refrigerant through the tank walls during this process.
1.A piston-cylinder containing air expands at a constant pressure of 150 KPa from a temperature of 285 K to a temperature of 550K.The mass of air in the cylinder is .05 Kg. Determine the system heat and work for the process