Warm water in a geothermal heating system enters the pipe of a radiator at 20 psia and 108°F with a flow rate of 207 cfm (ft³/min). The diameter of the pipe decreases from 3.3" to 2.4" inside the radiator, and heat is transferred from the water to the room at a rate of 1,083 BTU/s. Determine the temperature of the water when it leaves the radiator. Assume any changes in density of the water are negligible.

Warm water in a geothermal heating system enters the pipe of a radiator at 20 psia and 108°F with a flow rate of 207 cfm (ft³/min). The diameter of the pipe decreases from 3.3" to 2.4" inside the radiator, and heat is transferred from the water to the room at a rate of 1,083 BTU/s. Determine the temperature of the water when it leaves the radiator. Assume any changes in density of the water are negligible.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refrigerant-134a flows steadilyin a pipewith an inside diameter of 0.06m. The refrigerant enters the tube with a quality of 0.1, temperature of 36°C, and velocity of 10m/s. The refrigerans exits the tube at 9 bar as a saturated liquid. Determine the rate of heat transfer in kW. Cevap Sorunun cevabinı buraya giriniz
Water vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of 20 kPa and a dryness degree of 95 percent. In the condenser, there is heat transfer to the river water flowing through the pipes. The temperature rise of the river water is limited to 10 C to prevent thermal pollution. Since the state of the water at the condenser outlet is saturated liquid at 20 kPa pressure, what should be the flow rate of the cooling water.
Steam drives a turbine with a flow rate of 10000 kg/h. The steam enters the turbine at 60 atm and 300 C at a linear velocity of 40 m/s and leaves at a point 3 m below the turbine inlet at atmospheric pressure and a velocity of 250 m/s. The turbine gives shaft work (Ws') at a rate of 350 kW, and the heat loss (Q) from the turbine is 50 kcal/h. Calculate the enthalpy change (AH) within the process.
Steam at 1.6 MPa and 350°C enters a steam turbine at a flow rate of 16 kg/s. Thesteam leaves the turbine as a saturated vapor at 30°C. The turbine delivers 9 MW ofpower. A schematic of the turbine and its operating conditions are given in theFigure below. Determine the heat transfer rate from this turbine.
Subcooled water at 5°C is pressurised to 350 kPa with no increase in temperature, and then passed through a heat exchanger where it is heated until it reaches saturated liquid-vapour state at a quality of 0.63. If the water absorbs 499 kW of heat from the heat exchanger to reach this state, calculate how many kilogrammes of water flow through the pipe in an hour. Give your answer to one decimal place. Please provide correct solution Don't copypaste in chegg
The Refrigerating Effect of 94 tons of refrigeration is 127.75 kJ/kg. Determine the mass flow rate of the refrigerant.
The ducts of an air heating system pass through an unheated area. As a result of heat losses, the temperature of the air in the duct drops by 4°C. If the mass flow rate of air is 120 kg/min, determine the rate of heat loss from the air to the cold environment
3-10 A cooling tower is a device that cools spray water by passing it through a stream of air. If 15m³/s of air at 35°C dry-bulb and 24°Cwet-bulb temperature and an atmospheric pressure of 101kPa enters the tower and the air leaves saturated at 31°C, (a) to what temperature can this airstreams cool a spray of water entering at 38°C with a flow rate of 20kg/s and (b) how many kilograms per second of makeup water must be added to compensate for the water that is evaporated? Ans. 31.3°C, (b) 0.245kg/s.
Water vapor at a flow rate of 20000 kg / hour enters a steam boiler with a specific volume of 150 kPa 0.001053 m3 /kg. With the energy it receives from the fuel in the combustion chamber of the boiler, it rises to 1200 kPa at 150˚C. If the boiler has poor insulation and loses 100 kW of heat to the environment, calculate the time required to increase 1 ton of water to 150 ° C in the boiler.
In adiabatic process, the system has Q=max. value O W=0 O Q=0 O U-0 O * A vertical piston-cylinder device contains water and is being heated on top of a range. During the process, 65 Btu of heat is transferred to the water, and heat losses from the side walls amount to 8 Btu. The piston rises as a result of evaporation, and 5 Btu of work is done by the vapor. Determine the change in the energy of the water .for this process 61 Btu O 52 Btu 55 Btu 60 Btu * hp compressor in a facility that operates at full load-75 for 2500 h a year is powered by an electric motor that has an efficiency of 93 percent. If the unit cost of electricity is $0.11/kWh, the annual electricity cost of this :compressor is 16,540 $ 19,180 $ O 5,380 $ O 14,300 $ O barometric pressure or 1 atmospheric 1 pressure is equal to 1.019 kgf/cm2 1 kgf/cm2 0.9 kgf/cm2 0 kgf/cm2 O
Determine the rate of heat released (in kW) by the steam with 88.0% quality thatenters the evaporator at 1800 kg/h at 132C and exits as a subcooled liquid at 100C.Assume that the condensate outlet pressure is the same as the steam inlet pressure.The specific heat of liquid water is 4.187 kJ/kg-C
Q: Five hundred kilograms per hour of steam drives a turbine. The steam enters the turbine at 44 atm and 450°C at a linear velocity of 60 m/s and leaves at a point 5 m below the turbine inlet at atmospheric pressure and a velocity of 360 m/s. The turbine delivers shaft work at a rate of 70 kW, and the heat loss from the turbine is estimated to be 10ʻ kcal/h. Calculate the specific enthalpy change associated with the process.