A transformer has 800 turns on its primary winding and 160 turns on the secondary. The output is 150 kva at 2300 volts. Determine (a) the ratio of transformation, (b) the rated primary voltage, (c) the full load secondary current, and (d) the full load primary current, neglecting the no-load component.

A transformer has 800 turns on its primary winding and 160 turns on the secondary. The output is 150 kva at 2300 volts. Determine (a) the ratio of transformation, (b) the rated primary voltage, (c) the full load secondary current, and (d) the full load primary current, neglecting the no-load component.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.9P

See similar textbooks

Similar questions

3. Why the copper loss in the primary can be neglected, in the open circuit test? 4. Why the terms Rm and Xm significant when the transformer is loaded?
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Use germanium diodes.
Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires ( 6%) of rated voltage to circulate (90%) of full load current at power factor (0.25) when the low voltage winding is short circuited and the no load loss is equal to (2500 W). Transformer B: 6600/420 V, (600 KVA) requires (9%) of rated voltage to circulate (80%) of full load current at power factor (0.16) when low voltage winding is short circuited and no load loss is equal to (4500 W). Calculate the followings: If both transformers are connected in parallel to supply a load (1.2 + j 2.3) ohm, find the output power of each transformer.
Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires ( 6%) of rated voltage to circulate (90%) of full load current at power factor (0.25) when the low voltage winding is short circuited and the no load loss is equal to (2500 W). Transformer B: 6600/420 V, (600 KVA) requires (9%) of rated voltage to circulate (80%) of full load current at power factor (0.16) when low voltage winding is short circuited and no load loss is equal to (4500 W). Calculate the followings: The terminal voltage when transformer A is supplying half load at power factor (0.6) lagging and transformer B is supplying (85%) of full load at power factor (0.85) leading.
The windings of an 11500/2300V two winding transformer are connected in series, with 11500 V as the supply to the primary, to create an autotransformer. What is the voltage output of the resulting step-up autotransformer when Ip and Is are 10 A and 50 A, respectively?
Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols and quantities. Write the formulas to determine the total power P1, the transformation ratios and the primary current I1.
Determine the regulation of a transformer in which thepercentage resistance drop is 1% and the percentagereactance drop is 5% when the power factor 0.8 leading.
3. An 100-kVA, 2500/125-V, 50-Hz, step-down transformer has the following parameters: R₁ = 1.52, X₁ = 2.8 2. : R₂ = 15 m , : X₂ = 20m2,: Re - 3k, and: Xm 5 KQ. The transformer delivers 85% of the rated load at a terminal voltage of 110 V and a power factor of 0.866 lagging. Use the approximate circuit referred to as the primary. a. Determine the efficiency of the transformer. b. And the voltage regulation T
9. A single-phase transformer has a turn ratio of 6, the resistances of the primary and secondary windings are 0.9 £2 and 0.025 2 respectively and the leakage reactances of these windings are 5.4 92 and 0.15 2 respectively. Determine the voltage to be applied to the low- voltage winding to obtain a current of 100 A in the short-circuited high voltage winding. Ignore the magnetising current.
Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuit are 200 and 400 volts, respectively, and at a frequency of 50 Hz. The primary no-load current at a voltage of 200 volts is 0.7 amps and the losses in the core are 70 watts. The resistance and reactance of the primary are 3.2 and 1.25 ohms, respectively. Secondary resistance and reactance 6.0, 0.07 ohms, respectively. Draw the equivalent circle, showing the values of its elements.
Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no- load voltages in the primary and secondary circuit are 200 and 400 volts, respectively, and at a frequency of 50 Hz. The primary no-load current at a voltage of 200 volts is 0.7 amps and the losses in the core are 70 watts. The resistance and reactance of the primary are 3.2 and 1.25 ohms, respectively. Secondary resistance and reactance 6. 0, 0.07 ohms, respectively. Draw the equivalent circle, showing the values of its elements.
Figure 5 shows the core of a Linear Variable Differential Transformer (LVDT). S, S2 CORE Figure 5 Explain what happens when the core is at its maximum left, null and maximum right positions.