A tensile stress is applied along the long axis of a cylindrical brass rod thathas a diameter of 10 mm. Given the Poisson’s ratio for brass is 0.35,determine the magnitude of the load required to produce a 2.5 x 10-3 mmchange in diameter if the deformation is entirely elastic. Take the Young’sModulus (E) for brass as 10.1x104 MPa.

A tensile stress is applied along the long axis of a cylindrical brass rod thathas a diameter of 10 mm. Given the Poisson’s ratio for brass is 0.35,determine the magnitude of the load required to produce a 2.5 x 10-3 mmchange in diameter if the deformation is entirely elastic. Take the Young’sModulus (E) for brass as 10.1x104 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tensile stress is to be applied along the axis of a cylindrical brass rod with diameter of 200 mm. What is the load magnitude required to produce 2.8 x 10^-2 change in diameter if the deformation is entirely elastic?
The data shown in the accompanying table are From a tensile test of high-strength steel. The test specimen has a diameter of 0.505 in. and a gage length of 2.00 in. (see figure for Prob. 1.5-3). At fracture, the elongation between the gage marks is 0.12 in. and the minimum diameter is 0.42 in. Plot the conventional stress-strain curve for the steel and determine the proportional limit, modulus of elasticity (the slope of the initial part of thestress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 2.00 in., and percent reduction in area. TENSILE-TEST DATA FOR PROB. L.5-7 Laid (lb) Elongation (in) 1000 0.0002 2000 0.0006 6000 0.0019 10,000 0.0033 12,000 0.0039 12,900 0.0041 13,400 0.0047 13,600 0.0054 13,800 0.0063 14,000 0.0090 14,400 0.0102 15,200 0.0130 16,800 0.0230 18,400 0.0336 20,000 0.0507 22,400 0.1108 22,600 Fracture
A steel rod is subjected to a stress of 200 MPa and has Young's modulus of 200 GPa. Calculate strain.
A. Calculate the axial deformation of a steel rod 20 cm long, 10 cm diameter. If an axial loading 300 MPa is applied at the end. B. If the cross-sectional is square with t=10 mm, is the deformation will be higher or lower. (use E=200 GPa) * Vour onouIor
A rod is subjected to a uniaxial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. Calculate the modulus of rigidity if the poisson's ratio is 0.3.
Sketch two more stress-strain diagrams, again one for a ductile material and one for a brittle material. Draw the stress-strain diagrams so that the modulus of toughness for the brittle material is greater than the modulus of toughness for the ductile material.
Calculate the modulus of elasticity of the following material if it has a design stress of 250 kPa, the material is exposed to tensile stress and receives 15% of elongation from its original dimension. Express your answer in psi.
10-mm-diameter rod of 3003-H14 aluminium alloy is subjected to a 6-kN tensile load. Calculate the resulting rod diameter. Calculate the diameter if this rod is subjected to a 6-kN compressive load, given that the elastic modulus =70 GPa and poisson ratio=0.33
A circular rod of length 18 cm and diameter 5 mm is made of grade 1045 grade steel. a. Calculate the stress and strain in the rod, and its extension, when it is subjected to 7 kN of tension. (Express your answers using three significant figures.) |MPa E = x10-4 (Express your answer using whole numbers.) AL = | pm b. At what force would the rod begin to yield? (Express your answer using three significant figures.) F = |kN c. By what amount would the rod have to be stretched beyond its original length in order to yield? (Express your answer using whole numbers.) AL = um
A stress-strain diagram for a tension test of an alloy steel sample is shown in the diagram below. The initial sample diameter is 0.502”, the diameter of the fractured sample is 0.412”, the original gage length is 2.00” and the final length after fracture is 2.78”. Determine/ calculate the following: (a) The stress at the proportional limit. (b) The modulus of elasticity (E). (c) The yield stress using the 0.2% offset method. (d) Theultimatetensilestrength. (e) The rupture stress. (f) The percent reduction in area. (g) The percent elongation. (h) Is the material considered ductile or brittle?
A brass specimen of the circular cross-section is fractured at 159 kN force and the final length of the specimen at fracture is 51 mm. The fracture strength of the specimen is found to be 85 kN/mm2. The percentage of elongation of the specimen is 42 %. Determine the following 4-Stress under an elastic load of 14 kN 5-Young's Modulus if the elongation is 1.5 mm at 14 kN 6-Final diameter if the percentage of reduction in area is 27 %.
450-mm-long AISI 1020 steel rod is subjected to a tensile load of 55 kN. The allowable tensile stress is 140 MPa and the allowable total elongation is not to exceed 0.2 mm. Calculate the required rod diameter. The proportional limit is 175 MPa.