A single phase RL load connected 400 V, 50Hz supply and it draws lagging current. Calculate the current dawn from the source before and after the capacitor is connected in parallel. Also calculate power factor, real power, reactive power and apparent power before and after the capacitor is connected in parallel. Take Resistor, R= 80 Inductor, L= 0.9 H Capacitor, C= 9 µF

A single phase RL load connected 400 V, 50Hz supply and it draws lagging current. Calculate the current dawn from the source before and after the capacitor is connected in parallel. Also calculate power factor, real power, reactive power and apparent power before and after the capacitor is connected in parallel. Take Resistor, R= 80 Inductor, L= 0.9 H Capacitor, C= 9 µF

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
A 47-ohms load resistor is connected in series with a 10-uF capacitor. At what frequency will the capacitor reach the same value as the load resistor?
a capacitor and a resistor are connected in parellel to a 120 v 60 hz line the resistor has a resistance of 40 ohms and the capacitor has a capacitance of 132.6 uf what is the total current flow through the circuit. what is the impedence and the power factor and how many degrees out of phase are the current and voltage out phase with eachother.
An RC series circuit is connected is connected to 120V, 60Hz power source. The resistor is 25 ohms and has a voltage drop of 65 volts. What is the capacitance of the capacitor in uf?
By convention, the sign of reactive power to an inductance is and the sign of reactive power to a capacitance is
The attached image shows a circuit with an AC voltage source, a resistor, inductor, and capacitor connected in series. The circuit has the following characteristics: Resistor resistance: 10 ohm Capacitor capacitance: 0.05 F Inductor inductance: 13 H Current Amplitude: 4 A Voltage amplitude across the source: 60 V Frequency at the source: 0.3 Hz Voltage amplitude across the resistor: 35 V Voltage amplitude across the capacitor: 37 V Voltage amplitude across the inductor: 80 V (a) Calculate the RMS voltages from the amplitudes above. From the RMS voltages across the capacitor, inductor and resistor, calculate the RMS voltage of the AC source. Hint: Vrms = V0/sqrt(2) Vrms = sqrt( (Vrms,R)2 + (Vrms, L - Vrms, C)2 ) (b) Calculate the RMS value of the current (c) Using the resistance, capacitance, inductance, and the frequency of the AC voltage, calculate the impedance Z. From this, and the previously measured value of Vrms, find the RMS value of the current in the circuit.
A 206.0-2 resistor and a 2.80-µF capacitor are connected in series across the terminals of a sinusoidal emf with a frequency of 150 Hz. The inductance of the circuit is negligible. What is the impedance of the circuit?
Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 Vusing a single 14 V dc voltage source
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
In a series LR circuit, the reactance of the inductance is 520 ohm. What will be the value of the inductor if the frequency of the AC is 60 HZ?
the shunt capacitance is a capacitor O a. Between a phase and the ground O b. between phases and a phase to ground c. none of the answers O d. Between phases
What is the value of capacitance that needs to be connected in a parallel configuration to the load in order to correct the pf source to 0.94 lagging. Frequency f= 129 Hz