A rock vehičlé has thě föllówing data: Initial mass = 300 kg Final mass = 180 kg Payload mass = 130 kg Burn duration = 5 s Specific impulse = 280 s Determine the mass ratio, propellant mass fraction, propellant flow rate, thrust-to-weight ratio, and impulse-to-weight ratio of the vehicle.

A rock vehičlé has thě föllówing data: Initial mass = 300 kg Final mass = 180 kg Payload mass = 130 kg Burn duration = 5 s Specific impulse = 280 s Determine the mass ratio, propellant mass fraction, propellant flow rate, thrust-to-weight ratio, and impulse-to-weight ratio of the vehicle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

0 A crew return vehicle designed to launch humans from the surface of Mars to a low-Mars orbit requires a total AV ~4000 m/s. Assuming a single-stage-to-orbit design using LOX/CH4 at a trajectory-averaged Isp = 380 s, and = 2.8, calculate the fuel and oxidizer mass required to deliver a final dry mass of 17 metric tons to orbit.
The following data refer to a rocket engine, Velocity of jet = 1600 m/s Speed ratio = 0.7 %3D Fuel flow rate = 1kg/s Oxidizer flow rate = 4 kg/s Heat of reaction per kg of exhaust gases = %3D 2500 kJ/kg. impulse, propulsive efficiency, propulsive Determine, the thrust produced, specific power, thermal efficiency and overall efficiency of rocket enqine,
The following data are given for a certain rocket unit: Thrust, 8000 N Propellant weight flow rate, 36 N/sec Speed of rocket, 800 m/s internal efficiency32%combustion efficiency 97 % Determine (a) the effective velocity; (b) total kinetic energy per second (c) calorific value of propellant (d) the propulsive efficiency (e) the overall efficiency (f) the specific impulse (g) the specific propellant consumption ????? =1/3 ?(?^2) hV cylinder = ?(?^2) h V frustrum = 1/3 ?ℎ(?^2 +?^2 +? ×?)
QUESTION 1 (COLLAB) A new design of Saturn 17 rocket with mass 1.48 x106 kg has a propulsion engine that can eject gases at a constant speed of 241.89 m/s (vGas) by burning fuel at a rate of 2.11 x10 5 kg/s (dmdT). In full tank, the rocket can carry a fuel of mass 40.51 x10 6 If this design exceeds the velocity of 11,200 m/s it can can successfully escape Earth's gravity. Determine if this is so. Find its maximum velocity (velyz). (Pitch Angle = 0) kg.
2. Consider a two-stage rocket designed to provide an ideal AV of 3000 m/s. The following information is known: The following information is known: Payload mass = 100 kg 1st Stg: y = 0.9, Isp 250 sec, 45% of Total AV 2nd Stg: y = 0.85, Isp 300 sec, 55% of Total AV While the y values quoted above account for the propulsion systems, the interstage structure is generally treated separately. Assume that the weight of this component is equivalent to 5% of the mass of the Stg2/payload combination it supports. Determine: a) Stage 2 propellant and inert masses b) Interstage mass c) Total vehicle mass
A wind turbine testing laboratory provided the following results results: • Speed in the feed section = VA • Speed in the discharge section = VD • Feed (cross-section) area = A • Static pressure in the supply section = PA • Temperature in the feed section = T • Static pressure in the discharge section = Patm Estimate the reaction (strength) that the wind turbine will exert on the support with the information you collected in the tests. Take on that the air behaves like a perfect gas.
1 The following observations are recorded during a test on a four-stroke petro engine, F.C = 25cc of fuel in 10 sec, speed of the engine is 2600 rpm, B.P = 22 kW, Qair 0.00134 m, piston diameter 90 mm, density of the fuel = 0.85gm/cc , compression ratio = 7.5, CV of fuel = 42000KJ/Kg, room temperature = 24 °C %3D = 140mm, stroke length = %3D %3D %3D 2 A six-cylinder 4-stroke cycle petrol engine is to be designed to develop 250 kW of (b.p) at 2200 rpm the stroke / bore ratio is to be 1.3:1. Assuming nm =80% and an indicated mean effective pressure of 9.5 bar, determine the required bore and stroke. If the compression ratio of the engine is to be 7.5 to 1, determine consumption of petrol in kg/h and in kg/bp.hr. Take the ratio of the indicated thermal efficiency of the engine to that of the constant volume air standard cycle as 0.65 and the calorific value of the petrol as; 44770KJ/kg.
A solid propellant rocket motor was tested at sea level and following data were obtained: Propellant burn time = 34 sec Initial mass before test = 1400 kg Mass after test = 320 kg Average thrust = 85,000 N Chamber pressure = 8.0 MPa Nozzle exit pressure = 0.08 MPa Atmospheric pressure = 0.1013 MPa Nozzle throat diameter = 0.093 m Nozzle exit diameter = 0.312 m Calculate: (1) Mass flow rate m; (2) Exit velocity v2; (3) Characteristic velocity c*; (4) Effective exhaust velocity c; and (5) Specific Impulse I, at sea level. Draw the sketch of Chamber & Nozzle, and Show all calculations.
following data: operating data for pump 1 30 25 Ah, m Q, m³ /h 40 35 169 209 239 265 operating data for pump 2 25 Ah, m Q, m/h 30 35 136 40 203 267 Data for system Ah, m 20 25 30 35 244 372 470
Design a rocket nozzle, knowing that you have a chamber pressure of 6.28 MPa, mass flow rate of 1.23, and temperature of 825K.
Experiment Data Take the following data for the syringe injection pump Q/ Inner diameter of syringe barrel: D = 1.5 cm Inner diameter of the needle shaft of the syringe: d = 0.5 mm The thread pitch of lead screw: pt = 0.75 mm Lead screw rotation velocity (rpm): n Calculations a Liquid injection rate (cm³/hr) Q = pt*n* 60 * π * D²/4 Velocity of liquid in syringe barrel (cm/min) v₂ = 40/ (60** D²) Velocity of liquid in syringe needle (cm/min) v₁ = 40/ (60**d²) K 6- Find the rotation velocity of lead screw n and the velocity of liquid in syringe needle if the required injection dose is 1. 10 cm³ in 3 hours (continuous injection) 2. 20 cm³ in 12 hours (discontinuous injection, 5 cm³ each 3 hour, injection time = 1 min). Discus the reci Solution Calculate the liquid injection rate Q = P₁ xnx60xD² = 0.075xnx60××1.5² = 7.94n- cm² hr Calculate the velocity of liquid in barrel V₂ == 40 60xπx D² 4x7.94n 60xx1.5² = 0.07ncm hr Calculate the velocity of liquid in needle 40 60xπxd² 4x7.94n 60xπx…
B) The air flow to a four cylinder four-stroke engine is 2.15 m³/min. During a test on the engine the following data were recorded: Bore 10.5cm; stroke 12.5cm; engine speed 1200 rpm, torque 150 N.m, fuel consumption 5.5 kg/hr, calorific value of fuel, 43124 kJ/kg, ambient temperature 1-The brake thermal efficiency. and pressure are 20°C and 1.03 barş. Calculate: 2-The brakes mean effective pressure. 3-The volumetric efficiency.