The question is in the picture below. A pump motor in an industrial plant will start only if the temperature and pressureof liquid in a tank exceed a certain level. The temperature sensor and pressure sen-sor, shown in Figure 2.47 each produce a logic HIGH if the measured quantitiesexceed this value. The logic cirçuit interface produces a HIGH output to turn on themotor. Draw the symbol and truth table of the gate that corresponds to the action ofthe logic circuit.2.15TemperaturesensorLogicPumpmotorPressuresensorFIGURE 2.47 Problem 2.15: Temperature and Pressure SensorsAns:

The temperature sensor and pressure sensor is shown in the figure below, Both the sensors produce…

A pump motor in an industrial plant will start only if the temperature and pressure of liquid in a tank exceed a certain level. The temperature sensor and pressure sen- sor, shown in Figure 2.47 each produce a logic HIGH if the measured quantities exceed this value. The logic circuit interface produces a HIGH output to turn on the motor. Draw the symbol and truth table of the gate that corresponds to the action of the logic circuit. 2.15 Temperature sensor Logic Pump motor Pressure sensor FIGURE 2.47 Problem 2.15: Temperature and Pressure Sensors Ans:

A pump motor in an industrial plant will start only if the temperature and pressure of liquid in a tank exceed a certain level. The temperature sensor and pressure sen- sor, shown in Figure 2.47 each produce a logic HIGH if the measured quantities exceed this value. The logic circuit interface produces a HIGH output to turn on the motor. Draw the symbol and truth table of the gate that corresponds to the action of the logic circuit. 2.15 Temperature sensor Logic Pump motor Pressure sensor FIGURE 2.47 Problem 2.15: Temperature and Pressure Sensors Ans:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(b) Figure Q2(b) shows input waveforms of A, B and C. Draw the logic circuit that will generate the output waveform X. A Inputs B Output X Figure Q2(b) : Input and output waveforms
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
For the logic diagram shown in Figure 2, find logic function Q prove it is equivalent to Ex-NOR gate. i. A- DDO B
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Select a suitable example for for combinational logic circuit. O a. None of the given choices O b. De-multiplexer O c. PLA O d. Latches
Q2/A) Design 8x1 multiplexer using 2x1 multiplexer? Q2 B)Simplify the Logic circuit shown below using K-map then draw the Simplified circuit? Q2/C) design logic block diagram for adding 12 to 5 using full adder showing the input for each adder?
1. Design a combination circuit and write a logic circuit when there are 3 switches and 1 lamp, the lamp will light when there are at least 2 switches per circuit.
The following diagram shows a logic circuit using a combinatorial chip called A, and a sequential chip called B. Which wiring is legal, the wiring around chip A or the wiring around chip B. Select one: a. the wiring around chip A. b. the wiring around chip B.
What Is programmable logic arrays?
Y=f(A,B,C)=(0,4,5)+don't care(2)
A logic program produces set of logic data as depicted in the Table 2 below. This logic program consumed around of 1MB of memory space if it was to be stored in a PLC. However, the PLC is only capable of storing around half of the required size. (a) What will you do to solve this problem? (b) By using solution suggestion in question (a), propose the new logic function (c) Determine the type and numbers of logic gates are required for the new logic function (d) Draw the logic gate
Draw the logic circuit in the following figure?