Using Simple Logic Gates. Given: A Chemical plant needs a microprocessor-driven alarm system to warn of critical conditions in one of its chemical tanks. The tank has four (HIGH / LOW) switches that monitor: Temperature (T) Pressure (P) Fluid Level (L) Weight (W) To Find: Design a system that will notify the microprocessor to activate an alarm when any of the following conditions arise: High Fluid Level with High Temperature and High Pressure Low Fluid Level with High Temperature and High Weight Low Fluid Level with Low Temperature and High Pressure Low Fluid Level with High Temperature and Low Weight Note: Construct Truth Table. Draw Logic Diagram. Simplify Boolean equations using K-Map. Use Basic Logic Gates.

Using Simple Logic Gates. Given: A Chemical plant needs a microprocessor-driven alarm system to warn of critical conditions in one of its chemical tanks. The tank has four (HIGH / LOW) switches that monitor: Temperature (T) Pressure (P) Fluid Level (L) Weight (W) To Find: Design a system that will notify the microprocessor to activate an alarm when any of the following conditions arise: High Fluid Level with High Temperature and High Pressure Low Fluid Level with High Temperature and High Weight Low Fluid Level with Low Temperature and High Pressure Low Fluid Level with High Temperature and Low Weight Note: Construct Truth Table. Draw Logic Diagram. Simplify Boolean equations using K-Map. Use Basic Logic Gates.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

I need some help with the image provided. This is for microcontroller and embeded system. it seems is related to interrupts and it is providing some logical gates. Can someone explain wherever is happening in the image. I only need to grap the concepts nothing really technical
2. a) An electronic warning system has a switch labelled A and two sid. panels B and C. The output Q of an electronic warning system triggen an alarm if the enable switch A is turned on and either panel is open, o both are open. B and C produces an output of logic 0 signal when closed The enable switch A sends a logic 1 signal to the electronic system whes turned on. The system outputs a logic 1 to trigger the alarm. Draw a truth table for the electronic warning system described above. ii. May, 20 From the truth table, derive and minimize the canonical SOP Form Materia Draw the logic circuit for the electronic warning system Instruct minimisa sh. ananical Prnduet
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Question No.3: Consider a microprocessor based board which has 7-segment and Led is connected to it. Design an assembly language code such that input from user is taken; when user presses “1” “5410” should display on 7-seg Display and when user press 2 leds should glow 5 times in a loop. If any other key is pressed no action should be taken
Question: Consider you are asked to design a digital system that controls an electric motor “M". Motor is turned on when logic 0 is applied and turns off when logic 1 is applied. Two identical photo sensors, “S1" and "S2" produce logic 1 when light falls on them and provide logic 0 when light does not fall on them. Motor is to be controlled in such a way when light falls on both sensors, motor turns on. When light falls on S1 only, motor turns on. When light falls on S2 only motor turns off. Motor turns off when both sensors do not receive any light. Perform the following tasks: A. List the truth table. B. Write down the output equation. C. Draw the circuit diagram. D. Implement on Proteus (paste screen shot of implemented circuit).
4.a. What is the name of the nonprogrammable timer that is used to check the internal operation of the PLC?A. HousekeepingB. ScanC. WatchdogD. System4.b. Which one of the following terms is used to define the identifying letters placed above an input contact inladder logic?A. SurnameB. TitleC. StatementD. Locator
Design an interfacing system for solar controller, your design should monitor the solar system data like solar panels output, energy consumption, battery charging current, etc, the system must have keypad input and LCD display to allow users to view system status and adjust system parameters like max charging current, max consumption load. ...Draw a detailed block diagram of the interfacing system showing all the signals
5. a) Explain why a stop button must be normally closed and a start button must be normally open. b) Consider a case where an input to a PLC is a normally closed stop button. The contact used in the ladder logic is normally open, as shown below. Why are they both not the same? (i.e., NC or NO) start stop motor motor
Study the ladder logic program in figure below and answer the questions that follows: a) What type of timer has been programmed? Explain the timers function in detail with suitable graph: b) What is the length of the time-delay period? c) What is the value of the accumulated time when power is first applied? d) When does the timer start timing? e) When does the timer stop timing and reset itself? Input LS1 Outputs L1 TON L2 TIMER ON DELAY Timer Time base Preset KEN T4:0 LS1 ISOL A-o 1 10 KON) Accumulated SOL B- T4:0 SOL A DN T4:0 SOL B 3 DN T4:0 EN T4.0 EN
Arrange a circuit to implement the following logic: In a production system, conveyors are used to deliver workpieces from one place to another. The START (with memory) and STOP pushbuttons are used to activate (stand-by) and disable the system. In the stand-by condition, the conveyor motor will turn on if an object touches the first limit switch and will turn off if the object touches the second limit switch. The red-light flashes to indicate the conveyor is moving. If the conveyor is not moving, the green light will be on. Draw ladder diagrams and wiring diagrams!
Q. Choose the correct answer: 1. A PAL is a logic device which is: (a) one-time programmable (b) an erasable programmable (c) electronically erasable and programmable (d) both (a) and (b)
16) Answer each of the following with reference to the overfill alarm program shown in the figure below. a. Assume that the vessel is filling and has reached the 300-lb point. State the status of each of the logic rungs (true or false) at this point. b. Assume that the vessel is filling and has reached the 480-lb point. State the value of the number stored in each of the following words at this point: (1) I:012 (2) N7:1 c. Assume that the vessel is filled to a weight of 502 lb. State the status of each of the logic rungs (true or false) for this condition. d. Assume that the vessel is filled to a weight of 510 lb. State the value of the number stored in each of the following words for this condition: (1) I:012 (2) N7:1 18 e. With the vessel filled to a weight of 510 lb, state the status of each of the logic rungs (true or false). Inputs Ladder logic program Ouputs Fil Stop Start Full solenoid L2 Fill Fil solenoid solenoid Fill Filing solenoid Filing Full Ful GEQ GREATER THAN OR EQUAL…