A pile of diameter 0.4 m is fully embedded in a clay stratum having 5 layers, each 5 m thick as shown in the figure below. Assume a constant unit weight of soil as 18 kN/m³ for all the layers. Using - method (= 0.15 for 25 m embedment length) and neglecting the end bearing component, the ultimate pile capacity (in kN) is Y=18kN/m² for all layers G 7XXX 5m 5m 5m 5m 5m Pile Dia = 0.4m, L= 25 m c=40 kPa c=50 kPa c=60 kPa c=70 kPa c=80 kPa S XXX

A pile of diameter 0.4 m is fully embedded in a clay stratum having 5 layers, each 5 m thick as shown in the figure below. Assume a constant unit weight of soil as 18 kN/m³ for all the layers. Using - method (= 0.15 for 25 m embedment length) and neglecting the end bearing component, the ultimate pile capacity (in kN) is Y=18kN/m² for all layers G 7XXX 5m 5m 5m 5m 5m Pile Dia = 0.4m, L= 25 m c=40 kPa c=50 kPa c=60 kPa c=70 kPa c=80 kPa S XXX

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.21P: Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf...

See similar textbooks

Similar questions

2. Consider a group of 450 mm x 450 mm reinforced concrete piles were driven into thick loose sand layer with the average unit weight and internal friction angle of 16 kN/m3 and 30°, respectively. Estimate the group pile capacity with the arrangement as shown in Figure Q2 if the length of pile embedment is 30 m assuming ground water table is far below the ground surface. Use 8 = 0.80 and K = 1.5Ko. 3B 3B 3B 1 3 3.5B b 'P 9. 10 11 a 3.5B 2 4 1.5B 1.5B 1.5B 1.5B 1.5B 1.5B Figure Q2
Q1/ For the footing shown in Figure (1), estimate the pile group capacity. 0.6m dia bored pile Clay c=80 kN/m² y-17kN/m² S=1.5 m T L=12 m
A concrete pile 20 m long having a cross section of 0.46 m × 0.46 m is fully embedded in a saturated clay layer. For the clay, given: Yat = 18 kN/m², = 0, and Cu = 80 kN/m?. Determine the allowable load that the pile can carry (FS = 3). Use %3D the A method to estimate the skin resistance.
Find the maximum pile capacity for the pile group shown in figure below. If My = 500 kN.m and V = 7200 kN. 'My X=1.4 - x=1.4- y=1.2 y=1.2
In Problem 18.4, find the maximum bending moment in the sheet pile and determine the required section modulus, assuming an allowable stress of 190 MN/m2. 18.4 Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.
Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf = 3.05 m, and D = 0.406 m. The water table coincides with the top of the clay layer. Determine the total downward drag on the pile. Assume that = 0.6 clay. FIG. 18.26 Negative skin friction
12.20 A 600 mm diameter and 25 m long driven concrete pile car- ries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: E = 25 MN/m², Ep = 30,000 MN/m², and μ = 0.2
A concrete bored pile has a diameter of 800 mm as given in the figure below. Calculate the ultimate load carrying capacity of the pile. -0.8- Clay Cu = 60 kN/m² Y = 18 kN/m³ %3D 4m G.W.T Sand 6m $ = 30° Y = 20 kN/m³ Clay Cu = 100 kN/m² Y = 20 kN/m³ 5m
12.10 A concrete pile 15.24 m long having a cross section of 406 mm × 406 mm is fully embedded in a saturated clay layer for which Ysat = 19.02 kN/m³, p = 0, and c₂ = 76.7 kN/m². Determine the allowable load that the pile can carry. (Let FS = 3.) Use the a method Eq. (12.61) and Table 12.11 to estimate the skin friction and Vesic's method for point load estimation.
Consider a drilled, rough concrete pile with diameter B = 1m and length D = 10m embedded in a site underlain by a 5m thick layer of sand with fiction angle = 41 degrees and Ko = 0.5 that lies over an 8m thick layer of clay with fiction angle = 36 degrees, Ko = 0.38, and Su = 70 kPa. a. Determine the long term end bearing capacity of the pile. b. Determine the long term capacity of the pile.
A 30 cm diameter pile is driven 10 m deep into a homogeneous consolidated clay deposit. The safe load carrying capacity (in kN) against the factor of safety of 2.5. Take unit cohesion of clay as 40 kN/m² and adhesion factor as 0.7. A 150.8 B 105.6 C 215.4 D 115.7
Questions A group of 16 piles (4 in each row) was installed in a layered clay soil deposit shown below. The diameter of each pile is 500 mm and their c/c distance is 1m. The length of the pile group is 18m. Estimate the safe load capacity of the group with a factor of safety of 2.50. The adhesion factor (a) between the pile and soil in each soil layer are shown in the figure. 8 m 10 m C= 25 kPa;= 0°; a = 1.0 C₁= 40 kPa;p= 0; a = 0.7 TTTTTT Soil Profile O O O boor Plan View of pile group