A 600 mm diameter and 25 m long driven concrete pile car- ries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: E = 25 MN/m², E = 30,000 MN/m², and μ, = 0.2

A 600 mm diameter and 25 m long driven concrete pile car- ries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: E = 25 MN/m², E = 30,000 MN/m², and μ, = 0.2

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.21P: Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf...

See similar textbooks

Similar questions

11.10 A concrete pile 0.406 m x 0.406 m in cross section is shown in Figure P11.10. Calculate the ultimate skin friction resistance by using the a. a method b. A method c. ẞ method Use =20° for all clays, which are normally consolidated. 6.1 m 12.2 m 0.406 m Figure P11.10 Groundwater table Ysat Silty clay 18.55 kN/m³ Cu = 35 kN/m² Silty clay Ysat = 19.24 kN/m³ Cu = 75 kN/m²
Q1/ For the footing shown in Figure (1), estimate the pile group capacity. 0.6m dia bored pile Clay c=80 kN/m² y-17kN/m² S=1.5 m T L=12 m
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2 and ?s = 0.2.
A driven closed-ended pile, circular in cross section, is shown in Figure P 9.4.Calculate the following.a. The ultimate point load using Meyerhof’s procedure.b. The ultimate point load using Vesic’s procedure. Take Irr = 50.c. An approximate ultimate point load on the basis of parts (a) and (b).d. The ultimate frictional resistance Qs. [Use Eqs. (9.40 (L' ≈ 15 D)) through (9.42), and take K = 1.4 and ẟ' = 0.6 Φ'.]e. The allowable load of the pile (use FS = 4).
A concrete pile 20 m long having a cross section of 0.46 m × 0.46 m is fully embedded in a saturated clay layer. For the clay, given: Yat = 18 kN/m², = 0, and Cu = 80 kN/m?. Determine the allowable load that the pile can carry (FS = 3). Use %3D the A method to estimate the skin resistance.
Refer to the pile shown in Figure P 9.1. Estimate the side resistance Qs bya. Using Eqs. (9.40) through (9.42). Use K = 1.5 and ẟ' = 0.6 Φ'b. Coyle and Castello’s method [Eq. (9.44)]
12.2 A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Q, by a. Meyerhof's method b. Vesic's method c. Coyle and Castello's method Use m = 600 in Eq. (12.28). Concrete pile 460 mm X 460 mm Loose sand di = 30° y = 18.6 kN/m3 20 m F Dense sand $2 = 42° y = 18.5 kN/m
PILE FOUNDATIONS Example: 32/2 A reinforced concrete pile 30ft long and 15 inches diameter is embedded in a saturated clay of very stiff consistency. Laboratory tests on samples of undisturbed soil gave an average undrained cohesive strength c 2500 lb/ft². Determine the net pullout capacity and the allowable pullout load with F, =3. Take, alpha = 0.37
Problem 1. A 12-m-long 356-mm-diameter concrete pile is shown in Figure below. Estimate the allowable capacity, Qaul, of the pile. Use K = 1.3 Ko, 8' = 0.8 Ø' and a factor of safety equal to 3. 12 m Concrete pile 356 mm Loose sand $₁ = 30° y = 17.5 kN/m³ Dense sand $2 = 42° y = 18.5 kN/m³
12.2 A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Q, by a. Meyerhof's method b. Vesic's method c. Coyle and Castello's method Use m = 600 in Eq. (12.28). Concrete pile 460 mm x 460 mm 20 m Loose sand +1-30° y- 18.6 kN/m³ FIGURE P 12.2 Dense sand 2-42° y 18.5 kN/m³
Find the maximum pile capacity for the pile group shown in figure below. If My = 500 kN.m and V = 7200 kN. 'My X=1.4 - x=1.4- y=1.2 y=1.2
Example (3): A site consist of two layers of clay. The upper layer is 8m- thick and has an undrained shear strength of 80 kN/m². The lower layer is a thick layer which has an undrained shear strength of 120 kN/m². Assume • Top 1m of pile doesn't support load. • FS 1.5 and FS₁=3 = (A) Estimate the working load of the pie with the following: D=1.5m, Ds=4.5 m, L=27m Bell length is 3m. (B)Determine the length of 600mm- diameter of driven pile to support a working load of 1200 kN.